700184
17
Zoom out
Zoom in
Previous page
1/24
Next page
17
ENGLISH
FUNCTIONAL INSTRUCTIONS
Installation of RCA/Audio signal cables and power supply cables.
Ensure while installation not to lead the audio cables between the head unit and the amplier together with the power supply wires
on the same side of the vehicle. The best is a real separated installation on the left and right cable channel of the vehicle to avoid
interferences on the audio signal. This stands also for the enclosed bass-remote wire, which should not be installed together with the
power supply wires.
NOTE
15
If your head unit does not have a turn-on signal (REM), you can use the automatic turn-on function of the amplier. This works
in two ways, which can be set at the AUTO TURN-ON switch:
DC: This method only works if you use the amplier’s HIGH LEVEL INPUT. The amplier then detects a voltage rise to 6 volts
when the head unit is turned on by a so-called “DC offset” and then turns on the amplier.
VOX: Select this method when using the INPUT RCA jacks. The amplier then detects a voltage increase in the incoming audio
signal when switching on the head unit via the attached RCA cable and then switches on the amplier.
Note: As soon as the head unit is switched off again, the amplier switches itself off.
The terminal for the amplier turn-on (page 15#2, REM IN/OUT) can now be used to supply additional ampliers with a turn-on
signal. Simply connect the REM terminals of the two ampliers and make sure that the other amplier is in “normal” turn-on
mode, which means that the AUTO TURN ON function is disabled.
17
18
16
The REMOTE port is for connecting the cable of the included bass level remote controller. With this, the bass level can be e.g.
be adjusted from the driver’s seat. Only use the supplied bass remote controller and the associated cable. The bass level remote
controller only works in LP/BP mode (Low-Pass/Bandpass) on channel pair 3/4, in COPY mode under CH1/CH2 X-OVER also
on channel pair 1/2.
If your head unit does not have RCA preamp outputs, you can use the amplier’s HIGH LEVEL INPUT as the signal input. To do
this, simply connect the loudspeaker cables of the head unit to the enclosed cable plug as follows:
White: CH1 / left front +
White-Black: CH1 / left front –
Gray: CH2 / right front +
Gray-Black: CH2 / right front –
Green: CH3 / left rear +
Green-Black: CH3 / left rear –
Purple: CH4 / right rear +
Purple-Black: CH4 / right rear –
CH3
+
CH1
+
CH4
+
CH2
+
CH3
CH1
CH4
CH2
The BASS BOOST controller adjusts the bass boost continuously from 0 dB to +12 dB at 40 Hz on channel pair 3/4.
NOTE: Always use this controller with care. A permanently too high bass boost could damage your speakers!
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX QE900.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX QE900.4 in the language / languages: English, German as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info