700184
15
Zoom out
Zoom in
Previous page
1/24
Next page
15
ENGLISH
ELECTRICAL INTERCONNECTION
INSTALLATION INSTRUCTIONS
1
2
3
4
5
BEFORE CONNECTING
For the professional installation of a sound system, car audio retail stores offers appropriate wire kits. Ensure a sufcient prole section
(at least 25 mm
2
), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-
streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that all screws are xed tight after
the installation, because loose connections cause malfunctions, insufcient power supply or interferences. Do not set in the fuse until the
installation is accomplished.
GND
Connect the GND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short as
possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable
and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the battery to the ground point if
possible and enforce it if required. Use a ground wire with a sufcient cross section (at least 25 mm
2
) and the same size like the
plus (+12V) power supply wire.
REM IN/OUT
Connect a turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your head unit (REM) with the REM IN/OUT
terminal of the amplier. Use therefor a suitable cable with a sufcient cross section (0,5 mm
2
). Hereby the amplier turns on or
off with your head unit.
If you use the AUTO TURN-ON function, the REM IN/OUT terminal does not need to be connected. However, the REM IN/OUT
terminal can then connected to the REM terminal of another amplier to provide a control signal to it (REM OUT function).
+12V
Connect the +12V terminal with the +12V pole of the vehicle’s battery. Use a suitable cable with a sufcient cross section (at
least 25 mm
2
).
FUSE
The amplier inherently has no internal device fuse. Use the supplied fuse (100 A) with the fuse holder and install it in the power
cable between the 12 Volt positive pole of the vehicle battery and the +12V terminal of the amplier. The distance between the
fuse and the amplier should not exceed 30 cm.
ADDITIONAL CABLE FUSE (OPTIONAL)
Install an extra fuse (at least 100 A, not included) for the +12V power cable near the battery. The distance between the fuse and
the battery should not exceed 30 cm.
Replace defective fuses only with a new one of the same type and with the same fuse rating.
1 3
2
4
5
< 30 cm >
< 30 cm >
VEHICLE
BATTERY
100 A
min. 100 A
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX QE900.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX QE900.4 in the language / languages: English, German as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info