700184

ESX QE900.4 Manual

19
Zoom out
Zoom in
Previous page
1/24
Next page
19
ENGLISH
FUNCTIONAL INSTRUCTIONS
INTERCONNECTION EXAMPLE
2-channel-mode: 2 x Mono Subwoofer bridged
INTERCONNECTION
• Connect the RCA outputs of the head unit with the RCA jacks INPUT (CH /2) of the amplier with appropriate
high-value RCA cables. If a separate SUB OUT from your head unit is available, use this as line output.
• Connect the subwoofers with the SPEAKER OUTPUTS CH1/2 + BRIDGED - and CH3/4 + BRIDGED -.
• Always ensure that the total impedance load per channel pair is not lower than 4 ohms.
Too low impedance cause high temperature and will shut down the amplier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
INPUT MODE SWITCH
• Select the 2CH position on the INPUT MODE switch.
CROSSOVER SETTINGS & BASS BOOST CONTROLLER
• The X-OVER switch of CH1/2 must be in position COPY. All settings of channel CH3/4 will be adopted for CH1/2.
Note: The controllers HIGH PASS and LEVEL INPUT are then without function.
• The X-OVER switch of CH3/4 must be in position LP/BP. The cut-off frequency is adjustable with the LOW PASS controller of CH3/4
and should be set between 60 to 100 Hz, depending on the size of the subwoofer.
The HIGH PASS controller CH3/4 works also as subsonic lter, that eliminates the ultra-low, not audible frequencies to
generate a bandpass signal. The subsonic frequency should be set between 15 to 40 Hz, depending on the size of the subwoofer.
Note: If this value is higher than the LOW PASS setting, no sound is audible.
• The BASS BOOST controller allows a bass enhancement up to +12 dB.
LEVEL CONTROLLER CH3/4 (SUBWOOFER 1+2)
• Turn the LEVEL INPUT controller of the amplier to the MIN position.
• Turn the volume controller of the head unit to 80 - 90% of its full setting.
• Turn the LEVEL INPUT controller clockwise until you hear some distortion.
• Then turn back the LEVEL INPUT controller slightly until you hear a cleaner sound.
BASS REMOTE (SUBWOOFER 1+2)
• The enclosed BASS REMOTE CONTROLLER adjusts the bass-level e.g. from the driver’s seat.
Please use only the enclosed bass remote controller and cable.
Connect stereo RCA output (L/R or SUB OUT)
of the head unit with INPUT (CH1 / CH2) of the
amplier
LP/BP
COPY 2CH
Subwoofer 1
4 – 8 Ohms
Subwoofer 2
4 – 8 Ohms
Connect Bass Level
Controller with the
enclosed cable
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX QE900.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX QE900.4 in the language / languages: English, German as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info