617685
163
Zoom out
Zoom in
Previous page
1/198
Next page
The printed surface is scuffed or
soiled.
o
Is the media too thick or too thin?
Check media specifications to confirm that it is
compatible with the printer. If you are using a
software RIP, contact the manufacturer for
information on the settings and media that can be
used.
o
Is the media wavy?
Certain types of media may develop waves under
some conditions (humidity and temperature) while
installed in the printer. If a wave has developed, press
the d button in the control panel to feed the media
and avoid the affected area. We recommend that you
lower the temperature and humidity to prevent
waves developing.
o
Is the media creased or folded?
Media that is creased or folded may rise from the
platen and contact the print head, resulting in
smudges or uneven colors.
o
Are the wiper, caps, or print head stained?
Ink clots, lint or dust around the wiper, caps, or print
head may result in stains caused by ink drops. Clean
the affected area.
U “Cleaning” on page 103
o
Is the print head striking the printed surface?
If the printed side of the media is scuffed, select Media
Setup - Customize Settings on the control panel to
change Platen Gap according to the currently loaded
media.
If a scuff recurs after Platen Gap has been changed,
increase the value of Media Tension; this symptom
may be improved.
U “Customize Settings” on page 145
When Platen Gap or Media Tension has been
changed, perform Media Adjust again.
U “Media Adjust” on page 86
Areas secured by pressure rollers are
stained.
o
Are the pressure rollers stained?
Clean the pressure rollers.
U “Cleaning Inside the Printer (Once a week to once
a month)” on page 113
Nozzle clogs cannot be cleared.
o
Is cleaning being performed regularly?
If lint or dust adheres to the area around the print
head, caps (photo 1), wiper (photo 2), or flushing pad,
nozzle clogs may occur during printing. Moreover, if
the lint or dust is left adhered, nozzle clogs cannot be
cleared even after repeated head cleaning. Also, as
shown in photo (3), if a film of ink has adhered,
capping fails, causing a printing failure.
Clean the affected area periodically.
U “Cleaning” on page 103
o
Replace consumables.
If the problem persists after Head Cleaning has been
performed several times or regular cleaning has been
performed, the wipers or wiper cleaners may be worn
or deteriorated. We recommend that you replace
them when the following symptoms are detected.
Wiper: The wiper edge remains rough even after
stains were wiped off using the clean-room
wiper. Otherwise, the wiper is cracked.
Wiper cleaner: A film of ink has adhered to the
rear surface of the absorbent section.
U “Replacing the Wiper and Wiper Cleaner” on
page 120
Flushing pad: Ink has adhered to the surface, and
lint or dust cannot be removed.
U “Replacing the Flushing Pad” on page 122
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide
Problem Solver
163
163


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson SureColor SC-S50600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson SureColor SC-S50600 in the language / languages: English as an attachment in your email.

The manual is 6,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson SureColor SC-S50600

Epson SureColor SC-S50600 Installation Guide - English, German - 56 pages

Epson SureColor SC-S50600 User Manual - German - 217 pages

Epson SureColor SC-S50600 Installation Guide - Dutch - 56 pages

Epson SureColor SC-S50600 User Manual - Dutch - 182 pages

Epson SureColor SC-S50600 Installation Guide - French, Italian, Portuguese, Spanish - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info