20028
22
Zoom out
Zoom in
Previous page
1/107
Next page
LX#O
Service Manual
Pfvduct
LMacription
1.4.3 Hexadecimal Dump Function
The hexadecimal dump is a useful tool for troubleshooting data control problems. This section
describes how to run a hex dump.
1.
Turn on the printer while holding down the
LF/FF
and FONT buttons.
2. If paper is not loaded, the printer attempts it (either single sheet or continuous paper).
3. If the printer cannot load the paper, it indi~tes a paper-out error.
In
this
case,
insert
paper
again, and press the PAUSE button.
4. The printer waits for data after printing the message “Hex dump.”
5. Received data is printed as both hexadecimal codes and ASCII characters. If a corresponding
printable character does not exist, the printer outputs a period (.).
6.
Quit
hexadecimzd
dump printing by pressing the PAUSE button and tumingtheprinter off.
Note:
In
hex dump mode, the character table depends on the default
settin&
and 10
cpi
draft is
selected automatically.
1.4.4 Printer Status Indication
It describes how this printer indicates status and error conditions using
LEDs
and the beeper.
The symbols below describe the frequency of beeper sounds.
(
):
The beeper sounds
tbr
100 rns with an interval of 100 ms between beeps.
(—): The beeper sounds
for5~mswithan
interval
of100ms
between beeps.
While initialize signal is active:
During initialization:
Ready to print or printing:
Paper-out error:
Tear-off:
Operating error, fatal error:
1.4.5 Selected Font
PAUSE light is on.
PAUSE light blinks and beeper sounds
PAUSE light is off
Beeper sounds (
● ●
. )
and PAUSE light blinks.
(light
on:off
ratio=
6:1)
PAUSE light blinks (light
on:off
ratio=
1:6)
Beeper sounds (
————— ) and PAUSE light is on.
The combination of two FONT
LEDs
(1 and 2) is used to indicate the selected font.
Table 1-17. Font Selection
Selected Font
FONT 1
FONT 2
Roman
ON ON
Saris Serif
ON
OFF
Draft
OFF
ON
Draft condensed
OFF OFF
1.4.6 Paper Position Adjustments
To enter adjustment mode, press the PAUSE button for three seconds, until the printer beeps once
and the FONT lights blink to indicate that the adjustment operation is available. If the printer state
is not one of the conditions shown below, this operation is ignored.
. TOF position adjustment:
The position
mn
be adjusted just after the paper is loaded.
. Tear-off position adjustment:
The position can be adjusted when paper is actually located at the tear-off position.
In the adjustment mode, press the
LF/FF
button to feed paper forward and the FONT button to
feed paper backward. You can cancel adjustment mode bypressingthe PAUSE button or inputting
a print command.
The
adjusted position is stored in non-volatile memory.
Rev.
A
1-15
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson LX300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson LX300 in the language / languages: English as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson LX300

Epson LX300 User Manual - English - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info