749195
19
Zoom out
Zoom in
Previous page
1/48
Next page
19
IP2288EN
EN
WZ - Wizard
VC - Selection of closing speed
• LO: 15 cm/s
• ME: 20 cm/s (default)
• HI: 25 cm/s
D6 - Selection of device connected to terminals 1-6
• NO: none
• PH: photocells (default)
For other options, see the specific menu.
D8 - Selection of device connected to terminals 1-8
• NO: none
• PH: photocells (default)
For other options, see the specific menu.
RM - Radio receiver operation
• 1-3: Step-by-step
• 1-5: opening (default)
EP - Setting the coded area messages
If the possibility to receive coded messages is enabled, the control panel will be compatible
with remote controls of the “ENCRYPTED” type.
• ON: enabled
• OF: disabled (default)
SR - Remote control storage
When you press ENTER, SR starts to flash and you can associate the desired buttons. Once
OK is displayed, SR starts to flash again and you can associate the next button.
To quit, press ESC or ENTER for 2 seconds and go on to the next item.
NB: if NO flashes on the display, the remote control may already be stored.
CO - Saving of parameters
Here you can save the parameters that have previously been set.
• YS: to save and perform a card RESET
• NO: to quit without saving and go back to a blank screen (central part only)
NB: the CO item and YS/NO sub-menus flash constantly.
for 2 sec.
To save the configuration:
In the CO parameter select YS (yes) and press the ENTER button for 2 seconds.
When the configuration has been saved, a power reset is automatically performed on the card.
To quit without saving changes:
In the CO parameter select NO and press the ENTER button for 2 seconds.
Or: from any main parameter, press the ESC button for 2 seconds.
NOTES
The set values are only stored on the card if they are saved using the CO parameter.
The CO parameter and YS/NO options flash constantly.
When a configuration item is confirmed, it automatically moves on to the next parameter.
You can scroll through the menu parameters using the UP/DOWN buttons.
There is no automatic timeout function to quit.
Example
for 2 sec.
for 2 sec.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Entrematic Ditec ION6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Entrematic Ditec ION6 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info