717777

Energetics XT 1090 CROSSTRAINER Manual

9
Zoom out
Zoom in
Previous page
1/123
Next page
9
Step 2
1. Locate the Console Mast (12) and Console Mast Cover (49)
and slide the Cover onto the Mast as far as it will go. Make
sure the Console Mast Cover (49) is facing the correct way.
2. At the top opening of the Main Frame (1), there is a
Computer Cable (39) tied with a guiding wire. Unravel the
wire and feed the Computer Cable (39) it into the bottom
of the Console Mast tube (12) and out of the top opening.
3. Install the Console Mast (12) into the receiving bracket on
the top of the Main Frame (1).
NOTE: there is one bolt already installed in the receiving
bracket that will engage with the slot at the bottom of the
Console Mast. This needs to be tightened at the end along
with the three other console mast bolts.
4. Put the 1pc of 3/8" x 2T Split Washer (128) onto the 1pc of
3/8" x 2-1/4" Hex Head Bolt (75) and the 2pcs of 3/8” x 23
x 2T Curved Washers (104) onto the 2pcs of 3/8" x 3/4"
Hex Head Bolts (76). Install, and hand tighten them. The
3/8" x 2-1/4" Hex Head Bolt (75) should go through the left
side of the receiving bracket into the Console Mast (12).
NOTE: The Computer Cable (39) runs through the Console
Mast tube (12). Be careful not to damage or pinch this
cable during this procedure. Be careful as damage to the
Console Assembly (32) could result. Install, and hand
tighten the 2pcs of 3/8" x 3/4"Hex Head Bolts (76) with
3/8” x 23 x 2T Curved Washers (104) through
the front of the receiving bracket into
the Console Mast (12).
5. Use the 13/14m/m Wrench (124) to
tighten the three bolts, together with
the pre-installed screw, firmly. These
bolts should be tightened as much
as you possibly can.
6. Locate the Console (32)
and tighten it with the
4pcs of M5×10 m/m
Phillips Head Screws
(85) by using the
Phillips Head Screw
Driver (126).
7. There are 3pcs connectors at the top opening of the Console Mast (12), two Handpulse W/Cable
Assembly (44) and one Computer Cable (39). Connect these to the mating connectors on the back of the
Console (32). Do not force them while connecting as the connectors are keyed so that you cannot plug
them in the wrong way.
8. Store the excessive cables back into the Console Mast (12) and carefully install the Console (32) onto the
mounting plate of Console Mast (12) and secure the 4pcs of M5 x 10m/m Phillips Head Screws (85) by
using Philips head screw driver (126).
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Energetics XT 1090 CROSSTRAINER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Energetics XT 1090 CROSSTRAINER in the language / languages: English, German as an attachment in your email.

The manual is 2,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info