717777

Energetics XT 1090 CROSSTRAINER Manual

11
Zoom out
Zoom in
Previous page
1/123
Next page
11
Step 4
1. Align the hole in the end of the Connecting
Arms (L&R)(8&9)(pivoting rod end) with the
hole in the bracket of the Handle Bars
(L&R)(10&11). The rod end should be inside
of the Handle Bars (L&R)(10&11) bracket.
Take 2pcs of 5/16" x 1-1/4" Hex Head Bolts
(79) and install it through the Handle Bar
(L&R)(10&11) bracket and the rod end.
Install 2pcs of 5/16" x 20 x 1.5T Flat Washers
(155), 5/16" x 7T Nyloc Nuts (91) and Fish-
eye Sleeve (22) on the 5/16" x 1-1/4" Hex
Head Bolt (79) and tighten firmly by using
12m/m Wrench (129) and 13/14 m/m
Wrench (124) on the 5/16" x 7T Nyloc Nut
(91) and on the 5/16" x 1-1/4"
Hex Head Bolt (79).
2. Match Connecting Arm Cover
B (R)(163), with Connecting
Arm Cover B (L)(164), for
both sides of connecting
arms and tighten
with 2pcs of
M5 x 15m/m Phillips Head
Screws (82) and 4pcs of
Ø3.5x12m/m Sheet Metal
Screws (107) by using Short
Phillips Head Screw Driver
(125)
3. Repeat step 1 for the Connecting
Arm (R)(9).
4. Match the Connecting Arm Cover
A (R) (161), with Connecting Arm
Cover A (L) (162), onto the Handle
Bar (L) (10) and secure the covers with 2pcs of M5 x 15m/m Phillips Head Screws (82) and 2pcs of
Ø3.5x12m/m Sheet Metal Screws (107) by using the Phillips Head Screw Driver(126).
5. Repeat step 3 for the Handle Bar (R) (11).
6. Install the 2pcs of Sliding Wheel Cover (64) above the Slide Wheel, Urethane (47) and Pedal Arm (L,
R)(6,7) with the 4pcs of M5x12m/m Phillips Head Screws (82) and tighten them by using Phillips Head
Screw Driver (126).
7. Install the Rear Cover (A) (60), on the Rear Stabilizer of the Main Frame (1), with the openings facing
backward, and tighten the 2pcs of M5x15m/m Phillips Head Screws (82) by using the Phillips Head Screw
Driver (126).
8. Install the Rear Shroud (B) (61), above the Rail Assembly (2), with the openings facing the Rear Shroud
(A) (60), and guide the Sliding Wheel (47) into the Rear Shroud (B) (61).
9. Match the openings of Rear Shroud (B) (61), with Rail Assembly Cover (A) (60) and secure both covers
with 2pcs of 5x16m/m Tapping Screws (109) by using Philips Head Screw Driver (126). Secure the Rear
Shroud (B) (61), at the rear end with 2pcs of M5 x 50m/m Philips Head Screws (123).
PLEASE LOCK ALL COMPONENTS UP AFTER THE ACCESSSORIES HAVE BEEN ASSEMBLED.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Energetics XT 1090 CROSSTRAINER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Energetics XT 1090 CROSSTRAINER in the language / languages: English, German as an attachment in your email.

The manual is 2,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info