598275

Enduro AS1210 Manual

7
Zoom out
Zoom in
Previous page
1/36
Next page
enduro
®
AS1210 7
Ref: AS1210-UM-TKI-0412-Rev.A.
Reverse-polarity protection
This unit offers reverse-polarity protection, the RED “REVERSE” LED will illuminate and
the charging process will not start. If this happens, unplug immediately from mains,
connect the red crocodile clip to positive (+) battery post, and black crocodile clip to
negative (-) post, then plug into the mains power and the charging process will start.
Short-circuit protection
Should you accidentally touch the crocodile clips together whilst the mains power is on,
the unit will not perform charging. Unplug from mains, disconnect and start the process
again being careful not to touch the clips together.
Battery connection
The AS1210 has two options for connecting the unit to the battery:
• O-ring connectors for permanent fixation on your battery.
• Crocodile clamps for easy and flexible use. Please connect the rings to the clamps.
OPERATION
PLEASE READ CAREFULLY BEFORE USING
Suitable for 12V normal lead acid, sealed lead acid, gel, AGM and deep cycle
batteries between 14 - 230Ah and with 230VAC 50/60Hz circuit.
Preparing the battery
• Make sure you have a 12V normal lead acid, sealed lead acid, gel, AGM and deep
cycle battery and read battery user manual carefully.
• First remove the caps from each cell and check that the level of the liquid is sufficient
in each cell. If it is below the recommended level, top up with de-ionized or distilled
water.
Note: Under no circumstances should tap water be used. The cell caps should not be
replaced until charging is complete. This allows any gases formed during charging to
escape. It is inevitable that some minor escape of acid will occur during charging.
For permanently sealed battery, it is not necessary to carry out the above checks.
• Cleaning your battery terminals. Take care to keep corrosion from coming in contact
with your eyes.
• Be sure area around battery is well ventilated in charging process. When battery is
being charged you may notice bubbling in the fluid cause by battery generated
explosive gases during charging duration.
Connecting
• Connect the positive charging lead (red) to the positive terminal post of the battery
(marked P or +). Connect the negative charging lead (black) to the negative terminal
post of the battery (marked N or -). It is important to ensure that both DC clamps are
making good contact with their respective terminal posts.
• When using the AS1210 as a charger for car batteries installed in the car please do
not connect the minus „-“ directly with battery but on the chassis of the car. Please
make sure that the AC plug is not plugged in. The power has to be disconnected.
Please then connect the positive charging lead (red) to the positive terminal post of
the battery. As a next step please connect the negative charging lead (black) with the
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Enduro AS1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Enduro AS1210 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info