Manual Emtec H510 (page 11 of 74) (English, German, Dutch, French, Italian)

473755

Zoom out

Zoom in

1/74

2120

Advanced Settings, cont.

KidSafe

Press the HOME key, then select Setup, then select Advanced, then

KidSafe.

The first time you access the KidSafe menu you are asked if you want

to set up a KidSafe Code. If you select Yes, you see this screen. You

enter a 4 digit code that you will easily remember, but that your Kid(s)

won’t guess.

After you enter a 4 digit code and press OK you see a screen that lets

you pick a new KidSafe code, i.e., change it. And/or set the group of

favourites that your Kids have access to (the default group is Kids but

will be grayed out if you haven’t set that group up yet).

You can press the Side Key next to Pick Favourites and choose a

different favourites group that you want your Kids to have access to,

e.g., any other favourites group you’ve set up.

After you’ve done this you now have the option to Turn KidSafe On.

If you turn KidSafe On everything in the remote except access to the

KidSafe group (and Volume/Mute keys) is locked out. No settings

can be changed, and Prog Up/Down, and number keys don’t work.

If you try to access any other favourite group, change a setting, or access any forbidden menu,

you are asked to enter the KidSafe code. You cannot continue unless you enter the correct

KidSafe code. See the Troubleshooting section if you forget your KidSafe code - but don’t let

your kids read this owner’s manual!

Clearing Settings in the Remote

This lets you clear (erase) various things you’ve set up in the remote.

Press the HOME key, select Setup. Then at the screen to the right select

Clear Settings.

Pressing the Side Key next to Devices lets you clear the settings, i.e.

codes, for various Devices (TV, VCR, etc.). After selecting Devices,

you select the device you want to clear. Only devices that you have set

up are shown. All other devices that have not been set up are grayed

out.

Pressing the Side Key next to Favourites lets you select a group, e.g. ,

, etc., and then clear ALL the favourites you had set up in that group

of favourites. Only groups that you have set up favourites in are shown.

All other groups are grayed out.

Pressing the Side Key next to Learned lets you select a device (TV, VCR, etc.) that you had

previously learned commands under and clear everything that was learned. Only devices that

you have learned commands under are shown. All other devices are grayed out.

Pressing the Side Key next to Punchthrough lets you clear any Punchthrough commands you

had set up for a device. Only devices that you have set up Punchthrough for are shown. All

other devices are grayed out.

Pressing the Side Key next to Master Clear lets you clear EVERYTHING in the remote. Be

careful when selecting this. Note however that ALL the sections above display a warning

screen allowing you to change your mind before actually clearing anything.

Tips On Learning

a. Some functions from some types of remotes might not be able to be learned.

b. No functions may be learned under the HOME, MODE, FAVOURITE, , or (hard)

keys.

c. Use fresh batteries for both the H510 remote and your Original Remote.

d. Keep at least 1 meter away from incandescent or low-energy lights when learning.

e. Place the original remote end-to-end with the H510 remote so the IR transmitter (at the

top) on your original remote points at the IR learning device on the bottom of the H510

remote.

f. Keep the distance between the two remotes to approximately 3 cm.

g. Line up the remotes and then press the key you want to learn. To get the correct range,

press the key on the remote you are learning and you will see a “red halo” around the

transmit icon at the bottom left of the screen starts to flicker. The best range for learning

is when it flickers most rapidly. Move the position of the 2 remotes to achieve this. Do

not change this “best distance” between the two remotes until you have learned all the

required keys.

h. When Learning, you should normally not release the key being learned until the display

prompts you to do so. However, some keys might be learned multiple times if you do

this. If this happens just “tap” the key you want to learn, rather than press and hold it. For

example, keys that you normally hold down for a while (like volume up or down) will

likely require a long press when learning. Keys that you normally give a quick press (like

the numbers, and channel up/down) will likely require a quick press when learning. If

after learning say the channel up key, you find that it changes multiple channels when

pressed once, try relearning it with a short keypress.

i. If learning the first or second keys results in continuous errors then try the following:

1. Check the IR transmitters/sensors are correctly aligned between the two remotes.

2. Adjust the distance between the two remotes to be closer (e.g. 0.5 cm) or a further

away (e.g. 5 cm) from each other.

3. Try learning the original remote keys again.

4. If problems reoccur with the same key, check the original remote key being learned –

does it transmit? Does it operate the target device?

5. Clear all learned settings and try learning again.

Learning

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Emtec H510 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Emtec H510 Manual

Product: