536726
17
Zoom out
Zoom in
Previous page
1/62
Next page
15
status of the plug-in light fixtures or home appliances
without controlling via Smart Home Box.
LEARNING ID CODE
In order to communicate with the Smart Home Box, the
Smart Home Box will send ID code to the receiver. To
proceed with ID code learning:
1. In the front cover, there is an On/Off knob with
LED indicator.
2. Press the knob for 3 seconds until the LED
flashes rapidly, and then release the knob. The
receiver is about to learn the ID code.
3. Set the Smart Home Box into Home Automation
mode. Select ‘6-1 Green Control’, input Green
Control number and select ‘:1 Link Panel to
Receiver so as to emit the ID code to Green
Control.
4. If the receiver learns the ID code properly, the
LED will turn on and then off. If failure, re-try
step (2), (3) as mentioned above.
Note: DO NOT connect the receiver to light fixture,
electrical fans or other appliances to avoid possible
dangers which might be caused by ON/OFF test.
WALL SWITCH
INSERTING THE BATTERY
1. Using a flat screwdriver to detach the front case.
Fit the 23A 12V battery in the compartment with
battery leads ‘+’ to ‘+’ and ‘-‘ to ‘-‘.
2. By pressing the wall switch, the LED will illuminate,
implying that the battery has been inserted
properly.
EMITTING ID CODE
In order to communicate with the Smart Home Box, the
wall switch will send ID code to the Smart Home Box.
To proceed with ID code learning.
1. Set the Smart Home Box into Home Automation
mode. Select ‘6-2 Green Remote/Sensor’, input
Green Remote/Sensor number and select ‘:1
Learning ID’. Wait for the wall switch to send ID
code to the Smart Home Box.
2. Press the OFF knob, a command of OFF signal
and ID signal will send out. Keep holding the
OFF knob for more than 3 seconds until the Smart
Home Box learns the ID code successfully.
INSTALLATION
For the best results, fix the wall switch on a solid
surface, 1.2m above the ground. To affix the wall
switch to an existing wall box, simply secure the bottom
case to the wall box using the 2 screws provided.
Alternatively, you may use the double-side tape
provided to affix it anywhere you desire. After installing,
replace the front case.
TESTING THE WALL SWITCH
Ensure that the system is in Test Mode
On/Off Knob
LED Indicator
ON knob
OFF knob
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro HIS20SF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro HIS20SF in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info