Manual Elro HIS20SF (page 15 of 62) (English, German, Dutch, French)

536726

Zoom out

Zoom in

1/62

2. Fit the 3.6V Lithium battery supplied, with the

negative (-) towards the battery spring.

3. Mount the Detector to the fixed part of the frame

along the opening edge opposite the hinges using

either the double sided adhesive tape or screws

provided.

If fixing the Detector with screws; fit the Keyhole

slot in the top of the Detector over the head of the

smaller pan-head screw. Secure the bottom of

the Detector using the 12mm countersunk head

screw fitted within the battery compartment. You

will need to drill out the centre of the fixing screw

hole using a 3mm drill. Do not over tighten the

fixing screws as this may distort or damage the

casing.

4. Fit the Magnet to the moving part of the

door/window opposite the Detector using the

adhesive tape or 15mm fixing screws.

Ensure that the parallel gap between the Magnet

and Detector is less than 10mm and that the arrow

on the Magnet is pointing towards and aligned with

the mark on the Detector.

5. If several windows need to be protected, remove

the self-contained wired supplied and adopt the

wire according to the specifications as mentioned

below. This should be wired to the terminal block

provided in the battery compartment in series

connection. The wired contact should be

connected using two core (24AWG) wire of

maximum length 1.5m.

A cable entry cut-out is available and adjacent to

the terminal block.

6. Refit the battery cover.

SETTING THE MAGNETIC CONTACT

DETECTORS

1. Located on the PCB of the Detector is a

two-position DIP switch (SW2).

2. DIP switches 1-2 are used to enable/disable the

internal or external wired magnetic contact.

On/Off

Selection

DIP1 of SW2 DIP 2 of SW2

ON Internal on External on

OFF Internal off External off

Internal connection External wired connection

If setting the DIP1 & DIP2 to ‘Off’, only the internal

contact will be active. When two contacts are in

use for internal and external connection

simultaneously, one activation will be counted if one

of the contacts is opened; while both contacts must

be all close, the Detector will then be treated as

close.

3. If external contacts are wired to the Detector, set

the DIP1 to ‘Off’ and DIP2 to ‘On’.

IMPORTANT: If external contacts are not

connected, set the DIP1 to ‘On’ and DIP2 to ‘Off’

for the detector to operate correctly.

4. In order to communicate with the Smart Home Box,

the ID code of the Detector needs to be learned by

the Smart Home Box. To proceed with ID code

learning:

a. Set the Smart Home Box into ‘3. Security

Sensor Zone’ and press .

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elro HIS20SF in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elro HIS20SF Manual

Product: