708667

Elro AP5500 - Pro Alarm System Manual

41
Zoom out
Zoom in
Previous page
1/49
Next page
If the system is disarmed and the ‘ALARM MEM’ LED
is flashing with the panel beeping every few seconds,
this indicates that an alarm condition has occurred.
Use the Event Log to find out and make a note of
where the alarm occurred to assist in tracing the cause
of the alarm.
QUICK SET
To operate the quick set function and fully arm the
system in 5s, overriding the programmed exit delay.
Press
User Password
OMIT ZONE
To omit a zone from the next armed session:
Press
User Password
Scroll through the menu until the required zone is
displayed. The current setting will also be displayed.
To change the setting press .
Press to omit the zone, (i.e. zone omit ON).
Press to re-enable the zone, (i.e. zone omit
OFF).
After configuring zones to be omitted as required
Press to return to Standby mode.
Note: Omitting a zone will only affect the next armed
session. When the system is disarmed the omitted
zones will be re-enabled ready for the next armed
session.
PANIC ALARM
A full Alarm condition can be immediately initiated
at any time (whether the system is Armed or Disarmed)
in the event of threat or danger by activating a Panic
switch on either the Remote Control or the Control
Panel.
Remote Control:
Slide the Panic switch upwards.
Control Panel:
Press and hold the button for approximately
39 3 seconds.
The alarm will continue either for the alarm duration
when the system will automatically reset or until the
system is disarmed.
TAMPER
If the battery cover of any device is removed or if the
Siren or Control Panel are removed from the wall then
a Full Alarm condition will be initiated even if the
system is Disarmed. The alarm condition will continue
either for the alarm duration when the system will
automatically reset or until the system is Disarmed.
The ‘ALARM MEM’ LED on the Control Panel will flash
and the panel will beep every few seconds to indicate
an alarm has occurred.
Note: The Tamper protection facility on the Siren
operates independently. If the Tamper on the Siren is
activated this will not be indicated at the Control Panel.
CHIME
The Chime facility can only be operated with the
system in Standby mode.
Press to toggle the Chime facility between ON
and OFF.
Note: If the Chime is ON and the system is then armed
the Chime will remain ON after the system is disarmed.
EVENT-LOG
The Event Log will store the last 50 system Arm,
disarm, alarm and detector Low Battery events. The
Event Log will record the time, date and details for
each event. If when the system is disarmed the
“ALARM MEM’ LED is flashing and the panel beeps
every 10s, this indicates that an alarm has occurred.
To cancel the LED and stop the beeping you must
access the event log or press to eliminate the
flashing ‘ALARM MEM’ LED and the beeping as well.
To access the Event Log, (with the system in Standby):
Press .
The Event-Log will automatically start scrolling through
and displaying the event data starting with the most
recent event. The data for each event is shown on
two screens, each screen will be displayed for 5
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro AP5500 - Pro Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro AP5500 - Pro Alarm System in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Quick start guide - English - 8 pages

Elro AP5500 - Pro Alarm System Quick start guide - German - 10 pages

Elro AP5500 - Pro Alarm System Quick start guide - Dutch - 8 pages

Elro AP5500 - Pro Alarm System User Manual - Dutch - 42 pages

Elro AP5500 - Pro Alarm System Quick start guide - French - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info