Manual Elro AP5500 - Pro Alarm System (page 6 of 49) (English)

708667

Zoom out

Zoom in

1/49

happening in the protected property.

Answer phone and Voice-memo messages may also

be accessed remotely.

TAMPER PROTECTION

All system devices (except the Remote Control)

incorporate Tamper protection features to protect

against unauthorized attempts to interfere with the

device. Any attempt to remove the battery covers from

any device (except the Remote Control) or to remove

the Solar Siren or Control Panel from the wall will

initiate an alarm condition (unless the system is in Test

or Programming modes), even if the system is

Disarmed.

JAMMING DETECTION

In order to detect any attempts to illegally jam the radio

channel used by your alarm system, a special jamming

detection function is incorporated into the Control Panel

and Solar Siren. If this feature is enabled, and the

radio channel is jammed continuously for 30 seconds,

when the system is armed, the Solar Siren will emit a

pre-alarm series of rapid bleeps for 5 seconds. If the

jamming continues for a further 10 seconds or more a

full alarm condition will occur. In addition if the system

is jammed for more than three periods of 10 seconds in

a 5 minute interval, this will also generate a Full Alarm

condition.

The jamming detection features in the Control Panel

and Solar Siren operate independently.

The Jamming Detection circuit is designed to

permanently scan for jamming signals. However, it is

possible that it may detect other local radio interference

operating legally or illegally on the same frequency. If

it is planned to operate the jamming detection feature

we recommend that the system is monitored for false

jamming alarms for at least 2 weeks prior to leaving the

Jamming Detection function permanently enabled.

BATTERY MONITORING

In addition to the battery monitor and low-battery

indicators in each device, the Control Panel will also

indicate a low battery status within any Passive Infra-

Red or Magnetic Contact Detector on the system using

the Event log.

SYSTEM HOUSE CODE

In order to prevent any unauthorized attempt to operate

or disarm your system, you must configure your system

to accept radio signals only from your own system

devices. This is done by setting a series of eight

miniature (DIP) switches in all devices (except the

Control Panel) to the same ON/OFF combination (the

House Code) selected by the user/installer. The

Control Panel is then programmed to operate only with

devices set to this House Code. All detectors and

Remote Control Unit(s) must be configured with the

same House Code in order for the system to operate

correctly.

Inside the Siren, Detectors and Remote Control Unit is

a series of 8 DIP switches.

The House Code is set up by moving each of the 8

switches in each device to the same randomly selected

ON/OFF sequence. When setting the DIP switches,

ensure that each switch ‘clicks’ fully into position. Use

the tip of a ballpoint pen or a small screwdriver to move

each switch in turn.

Note: it is recommended that the system House Code

is always reset to a code other than the factory default.

ECE

1 2 3 4 5 6 7 8

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elro AP5500 - Pro Alarm System in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Quick start guide - English - 8 pages

Elro AP5500 - Pro Alarm System Quick start guide - German - 10 pages

Elro AP5500 - Pro Alarm System Quick start guide - Dutch - 8 pages

Elro AP5500 - Pro Alarm System User Manual - Dutch - 42 pages

Elro AP5500 - Pro Alarm System Quick start guide - French - 9 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elro AP5500 - Pro Alarm System Manual

Product: