668441

Elma 6700 Manual

45
Zoom out
Zoom in
Previous page
1/56
Next page
Elma 6700 side 45
4. To input a temperature offset value, press the softkey labeled Offset to open a
message box with the present offset value. Use and to position the cursor over
one of the digits or the polarity sign. Use and to scroll through the numbers for
each digit in the offset or switch between a + or – offset. With the desired value
displayed, press the softkey labeled OK to set the temperature offset.
Frequency Measurements
1. Set the function switch to the green Hz% position.
2. Insert the black test lead banana plug into the negative COM
jack. Insert the red test lead banana plug into the positive V
jack.
3. Read the Frequency in the display
Resistance Measurements
WARNING: To avoid electric shock, disconnect power to the unit under
test and discharge all capacitors before taking any resistance
measurements. Remove the batteries and unplug the line cords.
1. Set the function switch to the green Ω CAP position.
2. Insert the black test lead banana plug into the negative COM
jack. Insert the red test lead banana plug into the positive Ω
Jack.
3. Read the resistance in the display.
Continuity Check
WARNING: To avoid electric shock, disconnect power to the unit under
test and discharge all capacitors before taking any resistance
measurements. Remove the batteries and unplug the line cords.
1. Set the function switch to the green Ω CAP position.
2. Press the soft key labeled Menu. Move the menu selector to the
menu item labeled Beeper. Press the soft key Beeper.
3. Insert the black test lead banana plug into the negative COM
jack. Insert the red test lead banana plug into the positive jack.
4. If the resistance is less than approximately 25Ω, the audible
signal will sound. If the circuit is open, the display will indicate “OL”.
Diode Test
1. Set the function switch to the green Ω CAP position
2. Press the soft key labeled Menu. Move the menu selector to the
menu item labeled Diode. Press the soft key Diode.
3. Insert the black test lead banana plug into the negative COM
jack and the red test lead banana plug into the positive V jack.
4. Forward voltage will typically indicate 0.400 to 3.200V. Reverse
voltage will indicate “OL”. Shorted devices will indicate near 0V
and an open device will indicate “OL” in both polarities.
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elma 6700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elma 6700 in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 13,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info