Manual Elma 6400 LCR Meter (page 36 of 48) (English, Danish, Swedish, Norwegian)

668433

Zoom out

Zoom in

1/48

Elma 6400

• Auto power off

In order to extend the battery life, except of using external power supply, APO

feature will be helpful. It can be enabled or disabled APO function by press the

APO button and the LCD will show whether the function is enable or not. When all

function keypads do not be pushed or impedance range switching detected within

5 minutes, the system will launch the alarm buzzer beep at three times before the

auto power-off status. During the period of alarm, the meter will be kept in

operation by pushing any function key again. If any key is not in operation further,

the system power will be off.

• Buzzer

If the function keypad available is pushed,the buzzer output beeps once.If the

function keypad not available is pushed,the buzzer beeps twice.

• Backlight

When user push the button, the backlight will be active. Push the key

again to disable the backlight. When the backlight is active to last for 60 seconds,

the backlight will be disabled automatically.

• Battery detect

The meter will detect the battery multi-level voltages periodically. The LCD

indicators of battery life will be disappeared according to the decreasing of battery

voltage.

• Primary impedance with secondary parameter test mode

When AUTO/L/C/R function selection key is pushed, the main test mode

could be selected sequentially: Auto-LCR mode→Auto-L mode→Auto-C

mode→Auto-R mode→DCR mode→Auto-LCR mode. The default test mode is

Auto LCR mode which could check the type of impedance smartly and enter to the

L/C/R measurement mode automatically. The secondary parameter will follow the

L/C/R measurement. It means that (L + Q) , (C+D)2,(R+Q)2 are combined in one

group respectively. When Auto-L or Auto-C mode is selected, the impedance

measurement is auto ranging. The primary LCD display will show the inductance

or capacitance of DUT (device under test). The secondary LCD display will show

the quality or dissipation factor. The D/Q/θ/ESR value can also be shown by

pressing the button. When Auto-R(ACR mode) or DCR mode is selected, the

secondary parameter is omitted.

Note: When Auto-LCR mode is active, the secondary parameter will show the

equivalent resistance in parallel mode (Rp) to replace the D factor if the C

measured value of DUT is less than 5pF.

Note: Auto-LCR mode only. During Auto-R mode or DCR mode, the secondary

parameter is not available.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elma 6400 LCR Meter in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 0,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elma 6400 LCR Meter Manual

Product: