741487
10
Zoom out
Zoom in
Previous page
1/20
Next page
(((ELKRON)))
MP110 USER MANUAL
(((ELKRON)))
MP110 USER MANUAL
The acknowledgement of a correct code (keypad entry, reading of a key,
or mechanical key arming) immediately stops all alarms thay may be in
progress exception made for the telephone calls.
To lock the communicator (burglary events), it is necessary to disarm the
system from keypad, commutator, or mechanical key. If the communicator
has already started a transmission, the current call is completed and the
following voice calls are cancelled.
12. Lock of Alarm in Progress
The function allows the control unit receiving a telephone telemanagement
call from the engineer (FASTLINK+MODEM) to call back immediately after
checking the safety codes.
NOTE: the transponder function shall be enabled
The function is factory disabled and can be enabled only by the MASTER
USER with two different modes:
- mode A the control unit calls back the first MODEM type number among
the programmed numbers
- mode B the control unit calls back a specific telephone number sent by
FASTLINK
The following procedure is accessed:
1. Enter MASTER USER code
2. Press
F
+
TEL
9
+
ZONE
3
in sequence
3. The display will visualize : c 0 (default value)
4. By means of key
1
it is possible to select:
c A (call back - mode A)
c B (call back - mode B)
5. Press key
F
to confirm and exit from programming
13. Calling Back
31
5.
Display of Zone Status
The flashing of the led indicates that one or more alarms are
stored. Press the
A
key for a display of the stored alarms;
The message “ALARM ZONE nn” ’appears on the display (where nn
is the number of sensor, refer to the sensor table to know to which zone
it corresponds).
For a display in sequence of the other zones (inputs), press the
1
key consecutively. Pressing the
TOTAL
key during display will recall the
the first zone on the list. At the end of the list, the message “END OF
DATA” is displayed.
Press the
A
key.When there are no stored alarms the message
“NO DATA” is displayed.
The flashing of the led indicates that one or more intruders
are stored. Press the
S
key to display these.
The message ”TAMPER ZONE nn” appears on the display (where nn
is the number of the sensor, refer to the sensor table to know which
zone it corresponds to).
The flashing of the led indicates that there are one or more
open zones. Press the
O
key to display these.
The message “ZONE OPEN nn” will appear on the display (where nn
is the number of the sensor, refer to the sensor table to know which
zone it corresponds to).
5.1 Display of Stored Alarms
5.2 Display of Stored Intruders
5.3 Display of Open Zones
10
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron MP110MTG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron MP110MTG in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron MP110MTG

Elkron MP110MTG User Manual - German - 32 pages

Elkron MP110MTG User Manual - French - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info