Manual Elkron MP110MTG (page 8 of 20) (English)

741487

Zoom out

Zoom in

1/20

(((ELKRON)))

MP110 USER MANUAL

(((ELKRON)))

MP110 USER MANUAL

2.1 Storage of a New Key

1. Enter the MASTER USER code on the keypad and press keys

in sequence.

2. Press th

key several times until the following message appears

on the display:

• keypad with alphanumeric display: “KEY PROGRAM”

• keypad with segmented display: “-” (one flashing hyphen)

3. Press the

key. Commutator led 2 flashes slowly to indicate

system standby for entry of the first key.

4. Insert the commutator key. The system proposes key enabling on all

three zones with the lighting of leds 1, 3 and 4. If this is the desired

configuration, remove the key while led 2 flashes quickly.

5. By leaving the key permanently inserted, the various combinations of

zones with which the key can be associated are displayed with the

lighting of leds 1, 3 and 4, as shown in the table below:

6. When the desired combination has been set, remove the key ONLY

WHILE LED 2 FLASHES QUICKLY.

7. Re-insert the key. If the operation has been successfully

performed, the leds of the zones previously associated with the key

will light up and led 2 flashes slowly while standing by for the

programming of any other keys.

slow

flashing

led 1, 3

and 4 ON

1 1 ON 3 ON 4 ON the key is associated with all 3 zones

2 1 ON 3 OFF 4 OFF the key is associated with zone1

3 1 OFF 3 ON 4 OFF the key is associated with zone 2

4 1 ON 3 ON 4 OFF the key is associated with zones 1and 2

5 1 OFF 3 OFF 4 ON the key is associated with zone 3

6 1 ON 3 OFF 4 ON the key is associated with zones 1and 3

7 1 OFF 3 ON 4 ON the key is associated with zones 2 and 3

3.6 Disarming with Antirobbery Code

If the system is equipped with an integrated telephone unit or other remote

transmission system, a panic alarm signal can be sent in case of constraint

to disarm the antirobbery system.

• The disarming procedure described in para 3.1 is carried out, but it is

necessary to enter the secret code increasing the last digit by one unit.

• Example: code 123456 would become 123457; code 132459 would

become 132450.

• Disarm the control unit; if within approx.30 sec the correct code is not

entered the control unit will send the panic alarm to all programmed

telephone numbers.

3.7 Wrong Code

• In case of introduction of a wrong code for 4 consecutive times, the

system visualizes a tamper on the keypads and the readers. When

introducing a wrong code for the fifth consecutive time, the system starts

a tamper alarm.

3.3 Arming with Reduced Code

• It is sufficient to enter the first 2 digits of the code followed by key

TOTAL

for a total arming, or

for a partial arming.

• Quick arming is possible only if the system is fully disarmed.

3.4 Commutating Lock with Open Zones

• If the commutating lock with open zones has been programmed, it will

not be possible to arm –neither from keypad nor by DK key – the sectors

to which the currently open zones are associated. If you try such an

arming from keypad, a relevant warning is provided on the display and

no arming will take place.

3.5 Open Zone Self-Bypassing

• If both commutating lock and self-bypassing have been programmed,

the zones left open are automatically bypassed when an arming from

keypad or DK key is carried out. If the arming is made from keypad, the

self-bypassing is properly signalled on the display. The arming regularly

takes place and no alarm is generated. The self-bypassed zones are

reentered automatically at their re-closing (even with armed system).A

following opening will therefore generate the alarm.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elkron MP110MTG in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron MP110MTG

Elkron MP110MTG User Manual - German - 32 pages

Elkron MP110MTG User Manual - French - 120 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elkron MP110MTG Manual

Product: