741458

Elkron 80TC1L00133 Manual

69
Zoom out
Zoom in
Previous page
1/248
Next page
DS80TC1L-001 69
4.4.3 Focusing functions
The camera focus may be adjusted manually using the FOCUS +
and FOCUS – controls.
As the autofocus function is always on, a manual setting made using FOCUS + and FOCUS - will be kept only until a
pan, tilt or zoom command is used. In this case, autofocus will adjust focus automatically again.
Refer to the specific section for additional details on focusing and on the various options.
NOTE:
The autofocus function cannot work correctly in the following cases:
• The object to be focused on it not in the middle of the image
• There are far and near object in the frame
• Bright light is shining on the subject
• The subject is behind a glass pane covered in drops or dust.
• The subject is moving very quickly.
• The subject is not well lit.
• The subject is too big.
4.4.4 Iris opening functions
The iris opening may be controlled manually using the IRIS
and IRIS- commands.
The manual setting made using IRIS+
and IRIS- will be kept only until a pan, tilt or zoom command is used if the
automatic iris opening option is enabled (the default setting is on). In this case, the opening will be controlling
automatically again.
Refer to the specific section for additional details on iris opening adjustment.
4.4.5 Preset positions programming and recalling
The ELKDome camera can store up to 200 panning, tilting and zooming configurations (called preset positions) which
can be recalled at any time.
The manual focusing and iris opening settings cannot be stored.
NOTE:
When saving presets, remember that, from 51 to 63, from 78 to 101 and from 171 to 186, the presets are reserved and
cannot be saved or used to position the camera.
The following examples show how to program the free presets and recall them.
Example: programming preset number 32
1. Position the camera in a certain pan, tilt and zoom configuration.
2. Enter the command PRESET
+ 32 + ENTER
3. The setting is saved and the message “Stored” appears.
From this moment onwards, simply enter the command CALL
+ 32 + ENTER to move the camera to the preset
position.
NOTE: The saved value will be written over if the setting is reprogrammed.
The presettings are saved in a permanent memory area of the camera where they are maintained also when power is
disconnected. However, restoring default settings will delete all preset values.
Caution. The presettings store the coordinates according to an angular reference system. Therefore, the reference
system zero point may become misaligned with the camera mechanics after prolonged use of the tilting and panning
functions. Minor inaccuracies in preset positions may occur. In this case, calibrate the angular coordinate system using
the {DOME RESET} command. This calibration is automatically run when the camera is switched on.
… 69 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron 80TC1L00133 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron 80TC1L00133 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 5,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info