741458

Elkron 80TC1L00133 Manual

68
Zoom out
Zoom in
Previous page
1/248
Next page
DS80TC1L-001 68
4.4 CAMERA MOTIONS
After selecting a camera, it can be moved either directly using the control panel as described below.
• Panning (horizontal) and tilting (vertical).
• Zooming, focusing and iris opening.
• Preset positions programming and recalling.
These functions can be directly accessed using a single key or joystick or a simple key combination.
4.4.1 Panning (horizontal) and tilting (vertical) functions
The camera may be moved using the joystick on the Ref. 80KP9200133. Move the joystick vertically to tilt the camera
and horizontally to pan it.
The maximum pan span is from 0 to 360 degrees with continuous rotation. The maximum tilt span is from -5 degrees
(camera in vertical position) to 92 degrees (-92 degrees if the -
2 TILT LIMIT option of the CONTROL OPTIONS) menu is
enabled.
The panning and tilting speed can be modulated by operating the joystick appropriately.
However, it should be remembered that the maximum speed of rotation that can be obtained using the joystick is not
always equal to that set in the control options. In fact, it depends on the values of the PROPORTIONAL SPEED and
SPEED LIMIT options (in the MOTION menu) and zoom. If the value of these options is ON, the maximum speed of
rotation that can be obtained with the joystick is reduced proportionally to the enlargement adopted in order to improve
framing.
Panning (horizontal)
Tip the joystick rightwards to turn the camera horizontally clockwise and tip it leftwards to turn it anticlockwise.
If no advanced options are set (e.g. range limits set and enabled), the camera can be turned continuously without
interruptions.
The pan span may be limited between two angles in FUNCTION PROGRAMMING • MOTION • LIMIT OPERATION.
Tilting (vertical)
Tip the joystick upwards to turn the camera vertically upwards and tip it downwards to turn the camera downwards. The
camera rotation is limited upwards by the horizontal plane or downwards by the vertical axis.
Performance will change considerably near the vertical axis according to whether the AUTO FLIP is on or not (default
setting is on).
• With AUTO FLIP off, the camera will stop in perfectly vertical position and will stop turning when the joystick is
tipped downwards.
• With AUTO FLIP on, the camera will proceed over the vertical axis when the joystick is tipped downwards.
This is because, when the vertical axis is reached, the camera flips automatically by 180 degrees and resumes
the initial trajectory.
The AUTO FLIP function can be used to follow a subject arriving in a certain direction passes under the camera and
continues in a straight line. To do this, hold the joystick tipped downwards following the movement of the subject.
Observe that in this case the joystick performance after the camera passes over the vertical axis opposite to the normal
axis because tipping the joystick downwards will turn the camera upwards.
Normal operation of the joystick will be resumed as soon as the downward tip is interrupted (also only for an instant). At
this point, to follow the subject in the same direction, you will need to tip the joystick upwards, as you would normally.
4.4.2 Zoom functions
The camera frame may be adjusted by using the ZOOM +
and ZOOM - commands. Use ZOOM + to zoom into the detail;
use ZOOM -
to zoom out.
Enlargement can be set choosing from the values of optical zoom X28 80TC1L00133 or X36 80TC9K00133.
For further details, refer to the specific section of control mode settings.
… 68 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron 80TC1L00133 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron 80TC1L00133 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 5,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info