GB
12
7. Setting up the remote control
Insert batteries
1. Open the battery compartment cover.
2. Insert two new batteries. Be sure to observe the
correct polarity (+/-) of the batteries.
3. Close the battery compartment cover.
Notes
앬 The radio signal has a range of approx. 8 m.
앬 Use two alkali batteries, type R03 AAA (1.5 V).
앬 Always replace both batteries at once when you
can no longer see the LCD display.
앬 Never use a combination of new and used
batteries.
앬 Never use a battery type other than the specified
one.
앬 If the remote control is not used for a lengthy
period of time, remove the batteries to prevent
them leaking.
앬 The service life of the batteries if the remote
control is used normally is approximately 12
months.
앬 Dispose of spent batteries in the correct manner
at a public battery collection point.
Notes
Keep the remote control approximately 1 m from
television sets or other electrical appliances. Direct
sunlight may considerably reduce the range of the
remote control.
Objects between the remote control and the IR
receiver which can impede reception of the signal
must be avoided. Handle the remote control with
care. Do not drop it, keep it away from heat and
moisture so as not to damage the remote control.
8. Description of the remote control
functions (Fig. 3/4)
Button assignment
1. ON/OFF: Pressing this button enables you to
switch on the device. Pressing it a second time
will switch off the device.
2. MODE: Pressing this button allows you to select
the mode for the device. The mode will change
each time you press the button in the following
sequence: AUTO – COOL – DRY – HEAT –
FAN.
3. ^: Pressing this button increases the
temperature set for the room.
4. v: Pressing this button reduces the temperature
set for the room.
5. FAN: Pressing this button enables you to select
the fan speed. Each time you press this button
the speed will be switched in the following
sequence: LOW – MED – HIGH – AUTO.
The fan speed cannot be adjusted if the system
is set to AUTO or DRY modes.
6. SLEEP/TURBO: Pressing this button enables
you to select economy mode. Pressing it a
second time will deactivate this mode. The mode
will also be deactivated as soon as you press
another button. This function can only be used in
COOL, HEAT and AUTO modes.
TURBO: Not assigned.
7. SWING: Pressing this button will activate the
automatic direction change for the ventilation
flaps. The air flow is adjusted
upwards/downwards. Pressing the button a
second time will stop this function.
8. AIR DIRECTION: Pressing this button enables
you to fix the angle of the ventilation flap.
9. TIMER ON: Pressing this button enables you to
set the time at which the device will switch on
(0.5 – 24 hours). Each time you press this button
the activation time will move in steps of 30
minutes (steps of one hour after 10 hours). To
deactivate this mode, press the button as often
as required until the TIMER ON indicator
disappears from the display.
10. TIMER OFF: Pressing this button enables you to
set the time at which the device will switch off
(0.5 – 24 hours). Each time you press this button
the deactivation time will move in steps of 30
minutes (steps of one hour after 10 hours). To
deactivate this mode, press the button as often
as required until the TIMER OFF indicator
disappears from the display.
Display
21. TRANSFER SIGNAL: This symbol will be lit as
soon as the remote control transfers signals to
the indoor device. The indoor device will then
confirm with a signal tone.
22. OPERATING MODES: As soon as you press the
MODE button, the appropriate symbol for the
selected operating mode will appear.
23. TEMPERATURE DISPLAY: The set temperature
will normally be displayed here.
24. FAN SPEED display: If you press the FAN
button, the relevant symbol for the selected fan
speed will appear. The display will flash if the
system is set to DRY or FAN modes.
25. SLEEP / TURBO display: If you press the
SLEEP / TURBO button in heating or cooling
mode, the “Sleep” (energy saving mode) symbol
will appear. There is no “Turbo” function.
26. SWING display: The symbol will appear as soon
as you press the “Swing” button.
