Manual Einhell GE-BC 43 AS (page 25 of 112) (English, Danish, Swedish, Norwegian)

605943

Zoom out

Zoom in

1/112

- 25 -

6. Before starting

Each time before use, check the following:

•

That there are no leaks in the fuel system.

•

That the equipment is in perfect condition and

that the safety devices and cutting devices

are complete.

•

That all screws are securely fastened.

•

That all moving parts move smoothly.

6.1 Fuel and oil

Recommended fuels

Use only a mixture of unleaded petrol and special

2-stroke engine oil. Mix the fuel mixture as indica-

ted in the fuel mixing table.

Important: Do not use a fuel mixture which has

been stored for longer than 90 days. Important:

Never use 2-stroke oil with a recommended mi-

xing ratio of 100:1. The manufacturer’s warranty

will be voided in case of engine damage due to

inadequate lubrication. Important: Only use con-

tainers designed and approved for the purpose to

transport and store fuel.

Pour the correct quantities of petrol and 2-stroke

oil into the mixing bottle (see scale printed on the

bottle). Then shake the bottle well.

6.2 Fuel mixing table

Mixing procedure: 40 parts petrol to 1 part oil

Petrol 2-stroke oil

1 liter 25 ml

5 liters 125 ml

7. Operation

Please note that the statutory regulations gover-

ning noise abatement may diﬀ er from one loca-

tion to another.

Before starting up the equipment remove the pro-

tective caps from the cutting blade.

7.1 Starting with a cold engine

Fill the tank with the required amount of oil/petrol

mix. See „Fuel and oil“.

1. Set the equipment down on a hard, level sur-

face.

2. Press the fuel pump (primer) (Fig. 2/Item 29)

10 times.

3. Move the On/Oﬀ switch (Fig. 2/Item 9) to „I“.

4. Set the choke lever (Fig. 2/Item 17) to I I.

5. Actuate the decompression lever (Fig. 42/

Item 33).

6. Hold the equipment ﬁ rmly and pull out the

starter cable (Fig. 2/Item 14) until you feel it

begin to resist. Then tug sharply on the starter

cable 2 times.

7. Set the choke lever (Fig. 2/Item 17) to I

8. Hold the equipment ﬁ rmly and pull out the

starter cable (Fig. 2/Item 14) until you feel it

begin to resist. Then tug sharply on the starter

cable 4 times. The equipment should start.

Important: Never allow the starter line to snap

back. This may result in damage.

Once the engine has started, allow the equip-

ment to warm up for 10 seconds.

Important: Since the choke lever is secured,

the cutting tool starts to operate when the

engine is started.

Then release the choke lever by actuating the

throttle lever once.

9. If the engine does not start up, repeat steps

4-9 above.

Please note: If the engine does not start up even

after several attempts, read the section „Engine

troubleshooting“.

Please note: Always pull the starter cord out in

a straight line. If it is pulled out at an angle, then

friction will occur on the eyelet. As a result of this

friction, the cable will become frayed and will

wear away faster. Always hold the starter handle

when the cable retracts.

Never allow the cable to snap back when it has

been pulled out.

7.2 Starting with a warm engine

(The equipment has been idle for less than 15-20

min.)

1. Set the equipment down on a hard, level sur-

face.

2. Switch the On/Of switch to „I“.

3. Actuate the decompression lever (Fig. 42/

Item 33).

4. Hold the equipment ﬁ rmly and pull out the

starter cable until you feel it start to resist.

Then tug sharply on the starter cable. The

equipment should start after 1-2 tugs. If the

equipment does not start after 6 pulls, repeat

steps 1 – 9 of the procedure for starting the

engine from cold.

Anl_GE_BC_43_AS_SPK1.indb 25Anl_GE_BC_43_AS_SPK1.indb 25 09.10.13 17:4109.10.13 17:41

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GE-BC 43 AS in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 2,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell GE-BC 43 AS

Einhell GE-BC 43 AS User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 88 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell GE-BC 43 AS Manual

Product: