Manual Einhell GE-BC 43 AS (page 24 of 112) (English, Danish, Swedish, Norwegian)

605943

Zoom out

Zoom in

1/112

- 24 -

Sound and vibration

sound pressure level ........................ 97 dB(A)

uncertainty ..............................................3 dB

sound power level .......................... 113 dB(A)

Wear ear-muﬀ s.

The impact of noise can cause damage to hea-

ring.

In operation

Vibration emission value a

= 4 m/s

K uncertainty = 1.5 m/s

Reduce noise generation and vibration to a

minimum!

•

Use only equipment that is in perfect condi-

tion.

•

Maintain and clean the equipment regularly.

•

Adopt your way of working to the equipment.

•

Do not overload the equipment.

•

Have the equipment checked if necessary.

•

Switch off the equipment when not in use.

•

Wear gloves.

•

Wear eye and hearing protection

5. Assembly

5.1 Mounting the blade guard hood

Important: The cutting blade guard hood must be

ﬁ tted if you wish to work with the cutting blade.

The guard hood for the cutting blade must be ins-

talled as shown in Figures 10-11.

5.2 Joining the drive rod mechanism to the

connecting piece (Fig. 4-7)

Fit the handle screw (Item 10) as shown in Fig.

4. Open the handle screw and push the drive rod

mechanism (Item 4) into the connecting piece

(Item 5). Make sure that the centering lever (Item

R) latches in the guide hole (Fig. 5/Item H). Tigh-

ten the handle screw.

To take apart, undo the handle screw. Unlock the

centering lever and simultaneously pull the drive

rod mechanism out of the connecting piece.

5.3 Fitting / Replacing the cutting blade

The procedure for ﬁ tting the cutting blade is

shown in Figures 12-18. To dismantle, proceed in

reverse order.

•

Fit the carrier plate 30) onto the spline shaft

(Fig. 13)

•

Secure the cutting blade (1) on the carrier

plate (Fig. 14)

•

Place the pressure plate (31) over the thread

of the spline shaft (Fig. 15)

•

Plug on the cover of the pressure plate (32)

(Fig. 16)

•

Mount the nut (24) hand-tight (Fig. 17).

•

While pressing the locking lever (A), turn on

the nut until the carrier plate is held in posi-

tion. Tighten the nut with a suitable tool (Fig.

18). Important: Left-hand thread!

•

Check whether the blade (1) can rotate freely

after you let go of the locking lever. If this is

not the case, have the mechanism checked

by an expert.

5.4 Fitting the cutting line guard hood to the

blade guard hood

Important: The cutting line guard hood must be

ﬁ tted in addition if you want to work with the cut-

ting line.

The procedure for ﬁ tting the guard hood for the

cutting line is shown in Figures 19-20. A blade

(Fig. 19/ Item F) on the underside of the guard

hood automatically cuts the cutting line to the

optimum length. It is covered by a guard (Fig.

19/Item G). Remove the guard before you start

working and replace it when you have ﬁ nished

working.

5.5 Fitting the handle

Fit the handle as shown in Fig. 8-9.

5.6 Fitting / replacing the line spool

Fit the carrier plate (30) onto the spline shaft (Fig.

13)

While pressing the locking lever (A), turn on the

line spool until the carrier plate is held in position.

Tighten the line spool by hand (Fig. 21). Impor-

tant: Left-hand thread!

Check whether the line spool (3) can rotate freely

after you let go of the locking lever. If this is not

the case, have the mechanism checked by an

expert.

Anl_GE_BC_43_AS_SPK1.indb 24Anl_GE_BC_43_AS_SPK1.indb 24 09.10.13 17:4109.10.13 17:41

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GE-BC 43 AS in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 2,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell GE-BC 43 AS

Einhell GE-BC 43 AS User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 88 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell GE-BC 43 AS Manual

Product: