644116

Efco DS2800 Manual

40
Zoom out
Zoom in
Previous page
1/68
Next page
40
Italiano FrançaisEnglish
USE
UTILISATION
UTILIZZO
63 64A 64B
Sfoltimento
• La tecnica di sfoltimento consente di rimuovere tutta la
vegetazione indesiderata. Tenere la testina di trimmer appena
sopra il terreno e inclinarla. Lasciare che l’estremità del filo
colpisca il terreno intorno ad alberi, pali, statue e oggetti
analoghi (Fig. 60, pag. 40).
AVVISO: Questa tecnica comporta un aumento
dell’usura del filo.
• Il filo si consuma più velocemente e deve essere fatto avanzare
con maggiore frequenza quando lo sfoltimento viene eseguito
in prossimità di pietre, mattoni, cemento, recinti in metallo e
altro, anziché di alberi e staccionate in legno.
• Durante la rifinitura e lo sfoltimento, il motore deve funzionare
a un regime più basso di quello pieno per consentire una durata
maggiore del filo e ridurre l’usura della testina.
Taglio
• Il decespugliatore è ideale per tagliare l’erba difficilmente
raggiungibile con un normale tosaerba. Durante il taglio,
mantenere il filo in posizione parallela rispetto al terreno.
Evitare di spingere la testina contro il terreno per non rovinare
il prato e danneggiare l’unità (Fig. 63).
• Evitare un contatto costante della testina con il terreno
durante il normale taglio. Questo tipo di contatto costante
può danneggiare e consumare eccessivamente la testina.
Sfoltimento rapido
• L’effetto a ventaglio del filo rotante può essere utilizzato per
ottenere uno sfoltimento rapido e facile. Mantenere il filo
sopra il terreno da sfoltire in posizione parallela ed eseguire
movimenti avanti e indietro alternati (Fig. 64 A-B).
• Per ottenere risultati soddisfacenti nel taglio e nello sfoltimento
rapido, il motore deve funzionare a pieno regime.
ATTENZIONE: Non tagliare mai se la visibilità è scarsa
o in condizioni di temperature estreme o di congelamento.
Désherbage
• Le désherbage permet d’éliminer toute la végétation et les
mauvaises herbes indésirables. Maintenez la tête de coupe à fils
juste au-dessus du sol, en l’inclinant légèrement. Passez l’extrémité
du fil autour des arbres, des piliers, des statues et autres (Fig. 60).
MISE EN GARDE : Cette technique de coupe augmente
l’usure du fil.
• Le fil s’abîme plus vite et doit être changé plus souvent si la coupe
s’effectue autour de roches, de briques, de ciment, de clôtures
métalliques, etc., que lorsqu’elle s’effectue autour d’arbres ou de
clôtures en bois.
• Pour ces travaux, n’utilisez pas l’étranglement maximum comme
cela le fil durera plus longtemps et l’usure de la tête de coupe à
fils sera moins importante.
Coupe
• La tête de coupe à fils est idéale pour couper l’herbe difficile d’accès
avec une tondeuse à gazon. Le fil doit être parallèle au sol lors de
la coupe. Évitez d’appuyer la tête de coupe à fils contre le sol car
cela risque d’endommager la pelouse et l’outil de coupe (Fig. 63).
• Évitez que la tête de coupe ne soit en contact permanent avec le
sol pendant les travaux de coupe normaux. Les contacts de ce
type peuvent endommager la tête de coupe et contribuer à une
usure plus rapide de celle-ci.
Balayage
• L’effet de ventilateur du fil en mouvement peut être utilisé pour
un balayage rapide et simple. Pour cela, le fil doit être parallèle au
sol et maintenu au-dessus de la zone à balayer, un mouvement
d’avant en arrière devant être appliqué à la machine (Fig. 64 A-B).
• Pour les travaux de coupe et de balayage, utilisez l’étranglement
maximum afin d’obtenir de meilleurs résultats.
AVERTISSEMENT : N’effectuez jamais à un travail de
coupe par faible visibilité ou par températures extrêmement
élevées ou basses, ou par grandes gelées.
Clearing
• The clearing technique removes all unwanted vegetation.
Keep the trimmer head just above the ground and tilt it. Let
the end of the cord strike the ground around trees, posts,
statues and the like (Fig. 60).
CAUTION: This technique increases the wear on the
cord.
• The cord wears quicker and must be fed forward more often
when working against stones, brick, concrete, metal fences,
etc., than when coming into contact with trees and wooden
fences.
• When trimming and clearing you should use less than full
throttle so that the cord lasts longer and to reduce the wear
on the trimmer head.
Cutting
• The trimmer is ideal for cutting grass that is difficult to
reach using a normal lawn mower. Keep the cord parallel to
the ground when cutting. Avoid pressing the trimmer head
against the ground as this can ruin the lawn and damage the
tool. (Fig. 63)
• Do not allow the trimmer head to constantly come into contact
with the ground during normal cutting. Constant contact of
this type can cause damage and wear to the trimmer head.
Sweeping
• The fan effect of the rotating cord can be used for quick and
easy clearing up. Hold the cord parallel to and above the area
to be swept and move the tool to and fro (Fig. 64 A-B).
• When cutting and sweeping you should use full throttle to
obtain the best results.
WARNING: Never cut, when visibility is poor or in
very high or low temperatures or in freezing weather.
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco DS2800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco DS2800 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info