644116

Efco DS2800 Manual

38
Zoom out
Zoom in
Previous page
1/68
Next page
38
Italiano FrançaisEnglish
USE
UTILISATION
UTILIZZO
59
60
• Cercare di procedere in maniera ritmica. Rimanere saldamente
fermi con le gambe leggermente divaricate. Avanzare al termine
della corsa di ritorno e rimanere di nuovo saldamente fermi.
• Lasciare che la coppa di supporto sfiori il terreno. Serve a
evitare che il disco tocchi il terreno.
• Per ridurre il rischio di attorcigliamento di materiale intorno
al disco, attenersi alle seguenti istruzioni:
1. Tagliare sempre con il motore a pieno regime.
2. Evitare il materiale precedentemente tagliato durante la corsa
di ritorno.
• Arrestare il motore, sganciare il cinghiaggio e appoggiare l’unità
a terra prima di iniziare a raccogliere il materiale tagliato.
Taglio di erba con testina a fili di nylon
AVVISO: Non utilizzare un filo più lungo del diametro
specificato. Con la protezione montata correttamente,
l’apparato di taglio incorporato regola automaticamente la
lunghezza appropriata del filo. L’uso di fili eccessivamente
lunghi può sovraccaricare il motore e causare danni al
meccanismo di frizione e alle parti adiacenti.
Rifinitura
• Tenere la testina inclinata appena sopra il terreno. Il taglio
viene eseguito dall’estremità del filo. Lasciare agire il filo. Non
spingere mai il filo nell’area da tagliare (Fig.59).
• Il filo consente di rimuovere facilmente erba ed erbacce
alla base di muri, staccionate, alberi e cordoli; tuttavia, può
danneggiare la corteccia di certi alberi e arbusti e intaccare i
pali delle staccionate.
• Per ridurre il rischio di danneggiare altre piante, accorciare il
filo a 10-12 cm e diminuire la velocità del motore.
• Dans la mesure du possible, travaillez de façon rythmée.
Tenez-vous sur vos deux pieds, le poids également réparti.
Avancez après le retour de coupe et tenez-vous de nouveau
fermement sur vos deux jambes.
• Laissez le carter reposer légèrement sur le sol. Il est sert à
protéger la lame de tout contact avec le sol.
• Pour réduire le risque d’enroulement de débris autour de la
lame, suivez les instructions ci-dessous :
1. Coupez toujours à la puissance maximum.
2. Évitez le contact avec l’herbe déjà coupée au retour de coupe.
• Arrêtez le moteur, détachez le harnais et posez la machine sur
le sol avant de procéder au ramassage de l’herbe coupée.
Coupe d’herbe à l’aide d’une tête à fils
ATTENTION : La longueur du fil de coupe ne doit pas
excéder le diamètre de coupe prévu. Une fois la protection
appropriée montée, le dispositif de coupe règlera
automatiquement le fil à la longueur appropriée. L’utilisation
d’un fil trop long peut entraîner la surcharge du moteur et
endommager le mécanisme d’embrayage, ainsi que les pièces
à proximité.
Coupe avec une tête à fils
• Maintenez la tête de coupe à fils juste au-dessus du sol, à partir
d’un angle. L’extrémité du fil effectue tout le travail de coupe.
Laissez le fil travailler à son rythme. N’appuyez jamais le fil
dans la zone de coupe (Fig.59).
• Le fil permet de couper l’herbe et les mauvaises herbes qui
poussent au bord des murs, des clôtures, des arbres et des
bordures. Toutefois, il peut également endommager l’écorce
des arbres et les buissons ou encore les montants de clôtures.
• Pour éviter d’endommager les plantes, raccourcissez le fil
jusqu’à 10 à 12 cm et réduisez le régime du moteur.
• Try to work rhythmically. Stand firmly with your feet apart.
Move forward after the return stroke and stand firmly again.
• Let the support cup rest lightly against the ground. It is used
to protect the blade from hitting the ground.
• Reduce the riNL of material wrapping around the blade by
following these instructions:
1. Always work at full throttle.
2. Avoid the previously cut material during the return stroke.
• Stop the engine, unclip the harness and place the machine on
the ground before you start to collect the cut material.
Grass trimming with a trimmer head
CAUTION: Do not work with mowing line longer than
the intended diameter. With a properly mounted guard, the
built-in cutter will automatically adjust the line to its proper
length. Overly long lines can overload the engine, resulting
in damage to the clutch mechanism and nearby parts.
Trimming
• Hold the trimmer head just above the ground at an angle. It
is the end of the cord that does the work. Let the cord work
at its own pace. Never press the cord into the area to be cut
(Fig.59).
• The cord can easily remove grass and weeds up against walls,
fences, trees and borders, however it can also damage sensitive
bark on trees and bushes, and damage fence posts.
• Reduce the riNL of damaging plants by shortening the cord
to 10-12 cm and reducing the engine speed.
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco DS2800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco DS2800 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info