810921

Edilkamin Mito Idro Manual

16
Zoom out
Zoom in
Previous page
1/32
Next page
16
ENGLISH
- Must have a vertical expansion of not less than 30 cm.
After which the pipe can continue horizontally with a
gradient that fosters the flow of water.
- The diameter of the pipe must be at least one mea-
surement larger than the nominal measurement of the
discharge of the valve.
The end of the pipe must discharge into the sewer
system.
IT IS FORBIDDEN TO SHUT OFF THE DI-
SCHARGE
• Verify that the hydraulic system is correctly installed
and is equipped with an expansion tank that is sufficien-
tly large to guarantee safety.
The presence of a tank within the boiler-
stove does NOT guarantee appropriate pro-
tection from thermal expansion occurring in
the whole system.
Therefore the installer must assess whether
an additional expansion tank is needed, de-
pending on the type of system installed.
• Fill the system using the filling tap (it is recommended
not to exceed a pressure of 1,5 bar).
When filling, ‘bleed’ the pump and the relief tap.
• It is possible that it will be necessary to open the vent
(V - fig. 2)
during the initial days of operation to release
air in the system.
PLUMBING CONNECTION
The plumbing connection depends on the type of system.
However, there are some “common rules”:
• The plumbing connection must be carried out by qua-
lified personnel who can issue documentation declaring
correct installation conforming to current law in each
country (for example, in Italy according to Ministerial De-
cree 37/2008 and standard UNI 10412-2)
• The plumbing system must operate at a pressure
between 1 and 1.5-2 bar on a hot closed-vessel circuit.
Note: DO NOT install the stove in place of, for example,
a thermocooker installed with an open vessel without an
adequate expansion system making it a closed vessel.
• The separation of the primary from the secondary cir-
cuit is ideal and, in some countries, it is also mandatory
in case of the installation of a heating plant (for example,
in Italy, the reference is the Circular from ISPESL, now
INAIL, of April 2011).
This separation is easily carried out using KIT A2 from
Edilkamin.
• The presence of a puffer (inertial storage tank) is re-
commended but not mandatory. Its presence has the
advantage of freeing the stove from “sudden” demands
from the heating system and allowing the integration of
other heat sources. It reduces consumption and increa-
ses the efficiency of the system.
• The hot water exiting from the output of the stove must
be “directed” differently depending on the objective (hea-
ting, radiators, exchanger, whether or not there is a puffer,
etc.)
• The return temperature of the water at the stove must
be at least 50-55°C to avoid condensation. Depending on
the system, the installer must determine if anti-condensa-
tion valves or pumps are necessary.
• A puffer (inertial storage tank) is needed for heating
any installed low-temperature under-floor heating panels
according to the guidelines of the manufacturer of the
panels. The under-floor panels should not receive water
directly from the stove.
• The material used in the circuit must be suitable to
withstand any overheating.
• The discharge of the safety valve must be accessible
and visible.
The discharge water must be channelled into a vertical
pipe using a funnel with backflow air intakes, appropria-
tely spaced from the discharge point.
The conveying pipe must have the following characteri-
stics:
- Must not originate more than 50 cm from the discharge
of the valve and must be positioned in the same room
where the KIT is positioned.
INSTALLATION
B
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Mito Idro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Mito Idro in the language / languages: English as an attachment in your email.

The manual is 5.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Mito Idro

Edilkamin Mito Idro Usermanual and installation guide - German - 36 pages

Edilkamin Mito Idro Usermanual and installation guide - Dutch - 32 pages

Edilkamin Mito Idro Usermanual and installation guide - French, Italian - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info