810921
30
Zoom out
Zoom in
Previous page
1/32
Next page
30
ENGLISH
In the event of problems the boiler-stove stops automatically and runs the shutdown pro-
cess and the display shows text regarding the motivation of the shutdown (see the various
alarms below).
Never pull the plug during shutdown on account of malfunction.
To start the boiler-stove up again after a shutdown, let the shutdown procedure end (10
minutes marked by a beep) tand
then press the button .
Do not turn the boiler-stove on again before checking the cause of the malfunction and
CLEANING/ EMPTYING the crucible.
INDICATION OF POSSIBLE CAUSES OF MALFUNCTION AND INDICATIONS AND REMEDIES
(shown only on the control panel on board the boiler-stove):
1) Signalling: H1 (take action if the water temperature sensor is out of order or disconnected).
Problem: Shuts down due to the water temperature sensor being broken or discon-
nected.
Actions: - Check connection of the sensor to the control board.
- Verify functionality by means of a cold test
2) Signalling: H2 Failure of fume expulsion motor (this trips if the smoke extraction speed sensor
detects a fault)
Problem: Shutdown for smoke extraction speed fault detection
Actions: • Check smoke extractor function (devolution sensor connection) and board (DEALER).
• Check smoke channel for dirt
• Verify the electrical system and earthing system.
• Check eletronic circuit board (DEALER).
3) Signalling: SF (H3) Stop/Flame: (this trips if the thermocouple detects a smoke temperature lower
than the value set, which it interprets as the absence of flames)
Problem: Turns off due to drop in smoke temperature
Flame may fail for any of the following reasons:
Actions: - lack of pellets
- too many pellets have suffocated the flame, check pellet quality (DEALER)
• Check whether the maximum thermostat has caused the problem (rare circumstance since this
would
correspond to over heated fumes (technical assistance centre)
• Check whether the pressure switch has cut off electricity to the gear motor because of a blocked
flue or other
problem.
4) Signalling: AF (H4) Failed ignition (intervenes if a flame fails to appear within a maximum of 15 minu-
tes, or if ignition temperature is not reached).
Problem: Turns off due to incorrect smoke temperature during ignition
Distinguish either of the following cases:
Flame does NOT appear
Actions: Check: - combustion chamber position and cleanliness;
- arrival of combustion air in the combustion chamber;
- if the heating element is working (DEALER);
- room temperature (if lower than 3°C use a firelighter) and damp.
- Try to light with a firelighter.
Flames appear, but AF appears on the display after Ar.
Actions: Check: (only by the Dealer)
- if the thermocouple is working (DEALER);
- start-up temperature setting in the parameters (DEALER).
5) Signalling: H5 black out stop (not a defect of the boiler-stove).
Problem: Turns off due to lack of electricity
Actions: • Check electricity connection and drops in voltage.
6) Signalling: H6 broken or disconnected thermocouple
Problem: Turns off due to thermo coupling failed or disconnected
Actions: • Check connection of thermo coupling to board: Check function in cold test (DEALER).
TROUBLESHOOTING
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Mito Idro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Mito Idro in the language / languages: English as an attachment in your email.

The manual is 5.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Mito Idro

Edilkamin Mito Idro Usermanual and installation guide - German - 36 pages

Edilkamin Mito Idro Usermanual and installation guide - Dutch - 32 pages

Edilkamin Mito Idro Usermanual and installation guide - French, Italian - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info