810848

Edilkamin Double Manual

20
Zoom out
Zoom in
Previous page
1/62
Next page
20
ENGLISH
Igniting with cold hearth
1 Check that the ash bed is not too high.
Maximum height: 5 cm below the edge of
the panel.
If the ash bed becomes too high, there is a
danger that when opening the panel to add
wood, fragments of coal may fall out of the
hearth.
2. Completely pull the regulating control
(fig 7 - page 14) of the air valve in the
“switch on” position. Air for fuelling will
flow intensely to the wood in the hearth, to
rapidly reach high heating power.
3. The wood must be placed in the hearth
without excessively crowding it. Place an
igniter between the wood logs, and ignite.
The igniters are practical aids which ignite
only if placed underneath or in front of
wood waste. Attention: very large wood
logs do not ignite properly in a cold hearth
and free noxious gasses.
Never use material such as petrol, alcohol
and similar to ignite the hearth!
4. At this point, close the hearths panel
and supervise for a few minutes. Should the
fire go out, slowly open the panel, allocate
another igniter between the wood logs and
re-ignite.
5. Should the fire not require further
addition of wood, the moment the same
fire is exhausted, push the regulating lever
(fig. 7 - page 14) of the air valve in the
“maintain fire” position. Do not carry out
such regulation during the fuelling phase
and the release of noxious gasses, in
that, when the lever is in the maintain fire
position, the air flow for fuelling results
completely blocked. In case of sudden
oxygen flow (for ex. due to the opening of
the hearths panel) the “gasses still present”
in the hearth and in the eventual heat
recovery surfaces, may react violently with
said atmospheric incoming oxygen
Power supply with hot hearth
1 Pull the regulating control (fig 7 - page
14) of the air valve in the “switch on”
position and add the required amount
of wood in the hearth, placing it on the
existing coal. In this way, the wood will heat
up with the consequent expulsion of steam
and of the contained humidity. This leads
to a decrease of the temperature inside the
hearth. The volatile substances let out at
this point by the fuelling material require a
sufficient air flow, so that this critical phase
can be rapidly carried out and the required
temperature can be reached for the correct
fuelling.
A further suggestion:
For the initial ignition of the hearth, always
use the smaller wood logs. These rapidly
burn and therefore bring the hearth to
the right temperature in less time. Use the
larger logs of wood to re-power the hearth.
Certain types of wood briquettes inflate
once they are in the hearth, meaning they
stretch under the heat and increase in
volume. Always place the wood well inside
the hearth, nearly touching the rear wall of
the same, so that should it slide, it does not
fall in the panel.
USE INSTRUCTIONS
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Double at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Double in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0.93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info