663873

EdgeCraft Chef-s Choice Trizor XV - EdgeSelect 15 Manual

9
Zoom out
Zoom in
Previous page
1/16
Next page
9
Figure 5. Make certain the burr is present along the entire length of the edge. If there is no burr
or only a partial burr, continue to make additional pulls all in the left slot about five (5) at a time
and check for a burr after each group of five (5) pulls. In general 20-30 total pulls in the left slot
will be adequate to raise a burr; it is unlikely to take more than 50 left slot pulls to create the
burr. When a burr is confirmed, proceed to Step 2.
STEP 2
STROPPING/POLISHING THE FINAL EDGE ON TRADITIONAL JAPANESE BLADE IN STAGE 3
(RIGHT HANDED BLADE)
a. Make five (5) regular pulls 3-4 seconds each only in the left slot of Stage 3 (Figure 9) and
then proceed to remove any burr as follows:
b. Make one (1) regular pull in right slot of Stage 3 along the back side of the edge.
c. Make several fast pulls (one [1] second each) in the left slot of Stage 3.
d. Make one (1) fast pull in the right slot of Stage 3.
Check the blade carefully for sharpness using a thin sheet of paper. The blade should be razor
sharp. If not razor sharp repeat 3c and 3d above and retest the blade for sharpness.
NOTE: If your traditional blade is excessively worn or if the edge is chipped and irregular you can
use the left slot of Stage 1 to recondition the edge. Use the left slot only (for right handed blades).
Make as many pulls as necessary to reestablish a smooth uniform edge line. Use a black felt pen
to mark facet and follow progress of sharpening along the edge until edge line is restored. Then
proceed in Stage 2 and 3 as described on page 8 and this same page above.
RESHARPENING THE TRADITIONAL JAPANESE BLADE (RIGHT HANDED)
In general you will be able to resharpen quickly by following the sequence a thru d of Step 2 in
the preceeding section. Repeat this if necessary to obtain a razor sharp edge. When resharpen-
ing only in Stage 3 fails to develop a sharp edge or if the edge has been substantially dulled you
will need to re-hone the edge in Stage 2. Use only the left slot of Stage 2. Generally you will find
that about five (5) re-honing pulls will be sufficient in Stage 2. In any event develop a burr before
moving back to Stage 3. Finish the edge in Stage 3 following Step 3a, b, c, d.
SHARPENING LEFT HANDED TRADITIONAL BLADES
The procedure you must use with left handed blades is similar to that procedure for right handed
blades as detailed above – Except, in all cases the slots you must use are reversed. Where the
sharpening procedure for right handed blades calls for use of just the left slot, you must use only
the right slot when sharpening a left-handed blade. Likewise use the left slot where the right
handed instructions call for using the right slot.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice Trizor XV - EdgeSelect 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice Trizor XV - EdgeSelect 15 in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info