663887

EdgeCraft Chef-s Choice - Hybrid 220 Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
4
STAGE 1
To sharpen, place the sharpener on the table gripping it securely with your left hand. Push
on the power switch. Insert the knife blade, Figure 1, near its handle, into the far left slot of
Stage #1 and allow the left face of the blade to rest on the left face of the slot as you pull
the knife toward you. The knife edge should be in sustained moving contact with the internal
diamond coated disk. Only light downward force will be necessary as you pull the blade
toward you. Listen carefully to insure your knife maintains good contact with the diamond
disk. Take about 5 seconds to make each pull if you have a six inch (6”) long blade. Increase
the time of each pull for longer blades or decrease the time for shorter blades.
Make one pull of the blade in the left slot as described above and then repeat the same
procedure in the adjacent (right) slot of Stage 1. As you pull the knife thru the right slot, (see
Figure 3), allow the right side of the knife to rest on the right face of the slot. If your knife,
before sharpening, is not very dull you will find that only about 5 pairs of pulls, alternating in
the left and right slots of Stage 1, will be sufficient to put a keen edge on the blade. However,
if the knife is initially very dull you may find that 10 or more alternating pairs of pulls in the
left and right slots of Stage 1 will be needed the first time as you reshape and sharpen the
old edge. In Stage 1 always pull the blade toward you. Never push the blade away from you
when using Stage 1. Before leaving Stage 1 it is important to examine the knife edge to
insure there is a small burr along one side of the edge.
Figure 2 illustrates how to check for the burr. Proceed as follows: If your last sharpening
pull was in the right slot there should be a small burr on the right side of the blade edge.
If the last pull was in the left slot there should be a small burr along the left side of the edge. If
there is no burr make another pair of pulls and again check for a burr. Repeat making pairs of
Figure 1. Inserting the blade in the left slot of the
Stage 1. Alternate individual pulls in left and right slots.
Figure 2. Develop a distinct burr along knife edge
before honing in Stage 2. Burr can be detected by
sliding finger across and away from the edge.
Caution! See text.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - Hybrid 220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - Hybrid 220 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info