611763

Ebode IR Link Pro Flush Manual

5
Zoom out
Zoom in
Previous page
1/44
Next page
7-4-2011 Rev2 5 IR Link Pro Flush
1. Attach the 3IREDB Emitters onto the IR Sensor Windows of the components in your system that
you wish to control. Refer to Fig. 2.
2a. Plug the yellow mini plugs of the 3IREDB into one of the yellow labelled
"EMITTERS" jacks of the IRHUB4 Connecting Hub.
2b. Plug the IRQC cable into one of the yellow labelled “EMITTERS” jacks of
the IRHUB4, and the other side into the 3.5 mm mono IR input of your AVR.
IRED Mono TS 3.5mm pin configuration: tip is IR Data, sleeve is Ground.
(PLEASE CHECK THE MANUAL OF THE DEVICE FOR MATCHING PIN
CONFIGURATION)
3. Drill a hole 12 mm wide where you wish to position the IR Receiver. Remove the screw-nut, push
the receiver cable and thread through the hole with the lens facing into the room (and in line-of-
sight of your handheld remote). Screw the nut back on until tight to hold the IR Receiver in place.
4. Plug the red mini-plug of the IRLPRO Flush IR Receiver into the red labelled "IR RCVR" jack on the
IRHUB4 Connecting Hub.
5. Plug the 12VDC Power Supply into an unswitched 230V~50Hz outlet.
NOTE: It is important that you use an unswitched AC outlet so that the IR system is always active
for system power ON commands.
6. Plug the 2.1mm "C" plug of the Power Supply Adapter into the "+12VDC" jack on the IRHUB4
Connecting Hub.
STATUS
You can send a Power Status signal to the IRLPRO Flush IR Receiver by connecting a power
adapter to this connection (not supplied; 5 - 24VDC & 5 – 12VAC), which e.g. is switched by the
device to be controlled. When the A/V device or contact is switched on, the Amber Status LED
will light up in the IRLPRO Flush IR Receiver so that you can see that the A/V device is switched on.
(see figure 3). The input voltage range is 5 – 24 VDC & 5 – 12 VAC. Socket 2.1mm, pin
configuration: centre/red is ST/+VDC, sleeve/black is GND.
Fi
g
2
Fi
g
3
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ebode IR Link Pro Flush at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ebode IR Link Pro Flush in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info