Manual Ebode IR Link C (page 5 of 36) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

611753

Zoom out

Zoom in

1/36

10-8-2010 5 ebode IR LINK C

equipment with a remote room, your current hook-up should be similar to figure 1. If it isn't,

run a single length of RG59 or preferably RG6 cable from the Main Room to the Remote

Room.

NOTE: If RF amplifier(s), splitters or taps are used anywhere in the line of the coaxial cable

between the CPL Coupler and the INJ Injector, you must verify if those are DC passive in

order to be sure to route the IR commands through the amplifier(s) and splitters.

5. Installing the ebode IR Link C

INSTALLING THE IRLP IR RECEIVER

Insert the red mini plug attached to the

IRLP into the jack marked "IR RECEIVER"

on the INJ Injector. Refer to figure 2.

Plug the 12VDC Power Supply cord into

the jack marked "+12 V" on the INJ

Injector. Plug the power supply into a

230V~50Hz outlet after you have made

all other connections.

Position the IRLP IR Receiver so that the

InfraRed beam from the handheld

remote control has a direct view at the

front of the unit (within 10m). The

Receiver can be fixed to the surface

by using the double side tape pad or

via a slide on screw hole on the bottom of the unit.

INSTALLING THE INJ INJECTOR

Insert the "TO TV" plug on the back of the INJ Injector into "RF IN" on the TV in the Remote

Room. Connect the room-to-room cable to "ANT INPUT" on the INJ Injector.

INSTALLING THE CPL COUPLER

Insert the "SAT/VCR" plug on the back of the CPL Coupler into "OUT TO TV" on DVR in the

main room.

Connect the room-to-room cable to "REMOTE/TV" on the CPL Coupler, as shown in Fig. 2

INSTALLING THE 3IREDB TRIPLE IR EMITTER

Plug the 3IREDB Emitter into the jack marked "EMITTER" on the CPL Coupler in the main

room.

The emitters should be installed directly to the InfraRed sensor "window" on the front panel

of the satellite Receiver, DVR, cable box, etc. Simply remove the paper backing exposing

the adhesive surface of each Emitter and apply them to the centre of the sensor window.

NOTE: Although the IRED appears dark to the eye, it is transparent to InfraRed. Positioning

the IRED directly over the InfraRed window(s) of the component(s) will not block direct IR

control from a handheld remote.

ATTENTION: If you are only using one A/V appliance, then you do not need to use the

additional IR Emitters. Never remove it from the wire! Just dress up the wire and leave

close to the CPL.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ebode IR Link C in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ebode IR Link C Manual

Product: