515345
23
Zoom out
Zoom in
Previous page
1/32
Next page
23
9.2.1 Motion detector activated for presence verification
Symptom Cause and / or remedy
LED is on during WALK TEST, but no
alarm is triggered
In case of presence verification an alarm is only triggered, if no
motion has been detected over the programmed period ( time-out
can be selected according to section 5.1.2.1)
WALK TEST has been set, but LED is not
on
Power supply of the motion detector is missing (=> check cable,
connector and power supply)
Power supply not on since two minutes (stabilize time of PIR-motion
detector)
Alarming with announcement „emergency
call activated, sensor 1 activated “
Motion detector has been connected after the unit has been switch on!
Alarming with announcement „emergency
call activated, sensor failure “
Motion detector has been disconnected after the unit has been switch
on!
9.3 Sensor-1-contact
Symptom Cause and /or remedy
Sensor-1 does not trigger an alarm Inactive waiting period by switching on the unit or between two alarms
is not expired
Supervision has been temporarily deactivated (deactivation)
Supervision is deactivated at current position of the selection switch
(I/II/III) ( section 5.1)
Motion detection is programmed to verify presence ( section
5.1.2.1), an alarm is only triggered if no motion is detected over a
programmed time.
Test mode => check section 4.2.3
„Alarm due to sensor 1“ is announced, but
the motion detector has been temporarily
deactivated
The power supply of the unit has been cut off for a short period
The function switch has been switched to PROG or OFF after
temporarily deactivation.
9.4 Sensor-2-contact
Symptom Cause and /or remedy
Sensor-2 does not trigger an alarm Inactive waiting period by switching on the unit or between two alarms
is not expired
Supervision has been temporarily deactivated (deactivation)
Supervision is deactivated at current position of the selection switch
(I/II/III) ( section 5.2)
Sensor-2 is activated as an emergency button ( section 5.2.2)
Test mode => check section 4.2.3
„Alarm due to sensor 2“ is announced, but
the motion detector has been temporarily
deactivated
The power supply of the unit has been cut off for a short period
The function switch has been switched to PROG or OFF after
temporarily deactivation.
9.5 Sensor-3-contact
Symptom Cause and /or remedy
Sensor-3 does not trigger an alarm Inactive waiting period by switching on the unit or between two alarms
is not expired
Supervision has been temporarily deactivated (deactivation)
Supervision is deactivated at current position of the selection switch
(I/II/III) ( section 5.3)
Contact is still in alarm position. A new alarm can only be triggered,
after the contact returns to its rest position
Test mode => check section 4.2.3
9.6 Acoustical monitoring
Symptom Cause and /or remedy
noise is not triggering an alarm Factory setting supports monitoring of acoustics only on pos. III of
selection switch. ( programming can be altered, see section 5.4)
The unit has been deactivated by DTMF 7 => LED alternatively 4s
on / 4s off
By switching on the unit or after triggering an alarm, the acoustical
monitoring is not active during the waiting time of 20 seconds (
section 7.3) => LED is lit constantly during the waiting time!
Depending on the position of the selection switch, an alarm is triggered
with a different delay. Every time the noise exceeds the pre set level,
the LED is on. ( section 7.4)
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EasyAlarm CONTROL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EasyAlarm CONTROL in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EasyAlarm CONTROL

EasyAlarm CONTROL User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info