515344
8
Zoom out
Zoom in
Previous page
1/32
Next page
8
4.2 Operation with potential free alarm contacts (EasyAlarm BASIC)
4.2.1 Safety notes
Function switch must be shifted to OFF and telephone-cord must be disconnected before any wiring work is
done on the AC-adapter or connecting cable.
All contacts of the EXT port are on telephone circuit potential => therefore any applied alarm contact must be
potential free (relays or opto-coupler) and must have a isolation of lease 3.75kV according to regulation
EN60950.
All contacts have to be protected against any body contact
4.2.2 Installation
1. Slide function switch to OFF
2. Insert 9V battery into compartment on rear side of alarm unit
Please note: The telephone cord must be disconnected before opening the battery compartment because otherwise
you can get in contact with the telecommunication voltage!
Operation with alarm contacts Details according to section 5
3. Plug sensor-cord in one o the EXT/-port of alarm unit and connect potential free alarm sensor as following
FCC8/6
Plug
Open ends of sensor-cord
PIN 2: White wire (Output)
PIN 3: Black wire (Sensor-2 input)
CAN BE USED AS EMEGENCY MODE!
PIN 4: Red wire (+12V)
PIN 5: Green wire (Sensor-1 input)
PLUG&PROTECT-sensor
PIN 6: Yellow wire (GND)
PIN 7: Blue wire (Sensor-3 input)
CANNOT BE DISARMED!
4.2.2.1 Operation with only one alarm contact (Sensor-1)
If you need only one alarm contact you should use sensor-1-input. EasyAlarm
®
will auto-detect the contact-type (
Plug&Protect-Contact) and starts monitoring sensor-1 according to the state of the sensor-2-input at the time of power-up
(details according to section 4.1.4):
Sensor-1 is a normally closed contact => Connect Sensor-2-input to GND
Sensor-1 is a normally open contact => Leave Sensor-2-input open
4.2.2.2 Operation with up to three alarm contacts (NO or NC)
Select the appropriate contact to fit the monitoring!
Notes:
Sensor-1 monitoring can be disarmed (disable) or sensor-1 can be used for presence verification ( programming
according to section 5.1)
Sensor-2 monitoring can be disarmed (disable) or sensor-2 can be used as a emergency contact ( programming
according to section 5.2)
Sensor-3 monitoring CANNOT be disarmed ( programming according to section 5.3)
Connect power supply
4. Connect the AC-adapter cable into the other EXT/-port of the alarm unit
Telephone connection
5. Plug enclosed telephone-cord into -Line-Jack of alarm unit and connect it with the telephone network
If you share line with modem/telephone please proceed according to section 10.6
Sensor 1
Sensor 2
Sensor 3
Type of contact: Normally open (NO)
Normally closed (NC)
Potential free !
(to AC-adpter)
2
1
4
3
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EasyAlarm BASIC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EasyAlarm BASIC in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EasyAlarm BASIC

EasyAlarm BASIC User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info