515344
6
Zoom out
Zoom in
Previous page
1/32
Next page
6
4. SETUP
4.1 Operation with Plug&Protect motion sensor (EasyAlarm COMBI)
4.1.1 Safety instructions
Function switch must be shifted to OFF and telephone-cord must be disconnected before any wiring work is
done on the AC-adapter or Motion sensor cable.
All the electrical connections have to be potential free. Observe the regulation according to EN60950.
All contacts have to be protected against any body contact
Do not plug the phone cable (5) into the EXT/-jack, only into -line jack of
alarm unit (1)!
4.1.2 Mounting PIR-motion sensor
Choose the mounting location after careful consideration of the area to be protected.
The motion detector should be located so that an intruder will cross the infrared beam
pattern. If used to verify presence, a regular used room should be detected. Figure
shows the different infrared beam patterns at a typical mounting height of 2.5m.
Notes:
Do not mount detector towards direct sunlight or near to heat sources.
Do not mount detector behind items like glass or curtains because the infrared-
beam cannot penetrate them.
Keep away pets like cats or dogs from the protected area.
Do not protect the same area by more then one detector, because they can interfere.
4.1.3 Installation
1. Slide function switch to OFF
2. Insert 9V battery into compartment on rear side of alarm unit
Please note: The telephone cord must be disconnected before opening the battery compartment because otherwise
you can get in contact with the telecommunication voltage!
3. Connect the AC-adapter cable into one of the EXT/-ports of the alarm unit
4. Mount the motion detector and connect the cable to the other EXT/-port of the alarm unit
6. Plug AC-adapter to main socket
Test and adjust motion detector Details according to section 4.1.6
WALK-Test: Wait at least two minutes after power-up for the motion detector to be stabilised. After this time, check the
entire area by observing the LED. Adjust swivel if necessary.
Telephone connection
7. Plug enclosed telephone-cord into -Line-Jack of alarm unit and connect it with the telephone network
If you share line with modem/telephone please proceed according to section 10.6
Program calling number(s) Details according to section 6.1
8. Slide function switch to PROG
9. Enter * * <n> (selected calling number: Standard n = 1..9)
Corresponding calling number will be announced, followed by message “to modify press star“
10. Press * and enter calling number
11. Slide function switch to OFF
2
1
4
3
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EasyAlarm BASIC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EasyAlarm BASIC in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EasyAlarm BASIC

EasyAlarm BASIC User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info