633970

Durkopp Adler 267 - 2016 Manual

11
Zoom out
Zoom in
Previous page
1/28
Next page
9
3.3.2
Lifting the thread tension
- automatically with the "presser foot lift"
Bobbin thread
3.4
According to the sub-class, see the maximum limits of the suitable
bobbin thread in the table 1.1.
3.4.1
Winding the bobbin thread (fig. 3)
Pass the bobbin thread
- through the reel stand,
- from left through the rear hole in the thread guide U,
- clockwise between the disks around the adjustable bobbin winder
pre-tension U,
- from right back through the rear hole in the thread guide U,
- from left through the middle hole in the thread guide U,
- from right through the front hole in the thread guide U,
- counter-clock wise several times around the bobbin T,
- pass the excessive thread end in the knife for cutting it off,
- press the bobbin winder lever M. The winder will stop automatically.
- Pull the bobbin thread in the knife for cutting it off.
The bobbin winder pre-tension U should be set so Low that the thread is wound regularly at low tension.
When winding at an excessive pre-tension, the aluminium bobbins T may be separated and
considerable thread cutting disturbances may occur.
3.4.2
Bobbin change
For changing the bobbin,
- Move the thread take-up lever to its topmost point,
- Swing the lever B upwards (for arresting the presser foot in its upper position),
- Lift the flap and remove the bobbin case top from the hook,
- Place the other bobbin so that the bobbin rotates contrary to the thread pulling direction,
- Pull the bobbin thread under the spring d in the slit and advance
it from below through the hole for about 8,0 cm,
- Hold the bobbin case top with bobbin at the free thread end and place it into the hook,
close the fIap.
3.4.3
Adjusting the bobbin thread tension
Rule 1:
Work with the lowest possible bobbin thread tension.
Indication 1:
For correcting, turn the screw.
Rule 2:
For a lockstitch seam, the low bobbin thread tension can already be influenced during the winding
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 267 - 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 267 - 2016 in the language / languages: English as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info