578050

Dual Saw CS 490 Manual

27
Zoom out
Zoom in
Previous page
1/80
Next page
27
WARNING!
The saw blades were specifically developed for the DUALSAW. Saw blades of another type may be
used under certain circumstances. The use of other saw blades is not safe and may cause severe
injuries.
WARNING!
Disconnect the power cable from the socket and let the saw blades cool down before you remove
them.
FITTING THE FRONT HOLDING HANDLE
• Screw the front holding handle in the saw, as displayed in Figure 2.
• Tighten the holding handle with the bolt.
REMOVE THE SAW BLADES
1. Press the spindle lock to arrest the saw blade. (Fig. 3)
2. Turn the counter bolt using saw blade key. (Fig. 4)
3. Remove the counter bolt and the washer from the saw blade. (Fig. 5)
4. Open the bottom protective lid for the saw blade. (Fig. 6)
5. Lift the lid and remove Blade 1. (Fig. 7)
6. Lift the lid and remove Blade 2. (Fig. 8)
FITTING THE SAW BLADES
7. Establish which of the new DUALSAW saw blades is Blade 1 (Face 1) or Blade 2 (Face 2). (Fig. 9)
8. Open the bottom protective lid and apply Blade 2 on the saw on the external fitting shaft. (Fig. 10)
9. Place Blade 1 (Face 1) on Blade 2 (Face 2) and place both on the internal fitting shaft. (Fig. 11)
10. Place the washer and the counter bolt on the shaft. (Fig. 12)
11. Tighten the counter bolt with the saw blade key. (Fig. 13)
DUALSAW SAW BLADES
• Ensure that the saw blades are clean, sharp and correctly adjusted. When using blunt saw blades, the
saw is under greater strain and the risk of recoils increases. Keep the replacement saw blades ready so
that you can always use sharp saw blades.
• Resin and rubber-like residues on the saw blade slow down the cutting speed of the saw. Use a special
solvent for resin, hot water or a grease remover to remove adhesive residues. Do NOT use petrol.
OPERATION
PROTECTIVE LIDS FOR SAW BLADES
• The bottom protective lid placed on the saw serves your protection and your safety. On the protective
lid, NO modifications may be made UNDER ANY CIRCUMSTANCES. If the protective lid is damaged or
moves only slowly or not smoothly, the saw may NOT be used until the protective lid has been repaired
or replaced. Contact customer services. Maintain the correct operating position of the protective lid
while using the saw.
• The protective lid fulfils its intended use if it can move smoothly and subsequently returns to the closed
position. Contact customer services if the bottom protective lid no longer closes automatically before
you continue to use the tool.
WARNING!
Do not use the saw if the correct function of the saw blade protective lid is not ensured. The
protective lid should be checked before any commissioning of the saw for its operability. If the saw
falls to the ground, the bottom protective lid and the anti-shock bar must be checked for damage
and their operability for all cut depths.
EN
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dual Saw CS 490 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dual Saw CS 490 in the language / languages: English, German, Dutch, French, Italian, Turkish as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info