Manual DRU Lugo 80 (page 13 of 44) (English)

571624

Zoom out

Zoom in

1/44

English

INSTALLATION MANUAL

Connect the gas pipe as described in chapter 5.7.

Place the data plate (C) in the bracket in the bottom of the protective hood (D).

Hook the protective hood into bracket (A) and fasten it with the self-tapping screw;

Guide the flexible gas pipe that leads to the burner through the recess (2);

Guide the cables through the protected recess (3);

!Caution

Make sure the cables of the ionization pens and spark plugs do not touch metal parts, they should also not make

contact with signal and voltage cables.

Use cable ties to fasten cables and pipes.

!Caution

• There are 230V of mains voltage on the gas unit, and it must be guarded;

• Carefully observe the necessary safety instructions that also apply to the control hatch. (see chapter 5.5 to

5.7).

5.13 Mantel iron

If the chimney breast is made of stone-like material, it is necessary to place a mantel iron. A mantel iron must be

placed to prevent that the appliance has to carry the weight of the stone-like materials that were used to build the

chimney breast (masonry chimney breast).

Placing the mantel iron (see appendix 3, fig. 2d):

Cut the mantel iron to the correct size;

Position the mantle iron;

!Caution

Do not allow the mantel iron to rest on the construction frame.

Attach the threaded rod(s) in the nut(s) on the corner(s) of the mantel iron (A);

!Caution

Adjust the threaded rod(s) with tensioning nut(s) (B) so that there is sufficient room for adjustment.

Determine the height of the eye(s) (C);

Attach the eye(s) to the wall using the key bolt(s);

Attach the hook(s) (D) of the threaded rod(s) to the eye(s);

Level it all with the tensioning screw(s).

5.14 Glass panes

After placement of the wood set, it is possible to place the glass panes:

!Caution

• Avoid damaging the glass panes during removal/placing;

• Use the socket spanner supplied for loosening/tightening the self-tapping screws;

• If applicable, use the supplied allen key for loosening/fastening the allen screws;

• Avoid/remove fingerprints on the glass panes, as they will burn into the glass.

5.14.1 Removing the front glass pane

For removing the front glass pane, please observe the following steps.

Appliance with 3 sides of glass (see appendix 3, fig. 6):

If applicable, slide the lower decorative strip (A) towards the front, it does not have to be removed completely;

Unscrew the self-tapping screws from the upper glass strip and remove the upper glass strip (B);

Grab the glass pane at both sides;

Slightly tilt the top of the glass pane towards you;

Lift up the pane and tilt it forward at the bottom;

!Caution

Make sure you do not damage the glass pane.

Remove the glass pane.

Appliance with 2 sides of glass (see appendix 3, fig. 7):

If applicable, slide the lower decorative strip (A) towards the front, it does not have to be removed completely;

Unscrew the allen bolt of the vertical decorative strip (C) located at the long pane side;

Grab the vertical decorative strip at the top, tilt the vertical decorative strip and remove it;

Unscrew the self-tapping screws from the vertical glass strip (D) and remove the vertical glass strip;

Unscrew the self-tapping screws from the upper glass strip and remove the upper glass strip (B);

Place the suction cup (E) on the front pane on the closed side of the appliance;

Grab the pane at the suction cup and side and slightly tilt the top towards you;

Tilt the glass pane and move it sideways;

!Caution

Make sure you do not damage the glass pane.

Tilt the bottom of the glass pane towards the front and remove the glass pane.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DRU Lugo 80 in the language / languages: English as an attachment in your email.

The manual is 4.96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU Lugo 80

DRU Lugo 80 User Manual - English - 28 pages

DRU Lugo 80 User Manual - German - 28 pages

DRU Lugo 80 Installation Guide - German - 44 pages

DRU Lugo 80 User Manual - Dutch - 28 pages

DRU Lugo 80 Installation Guide - Dutch - 44 pages

DRU Lugo 80 User Manual - French - 28 pages

DRU Lugo 80 Installation Guide - French - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DRU Lugo 80 Manual

Product: