571631
13
Zoom out
Zoom in
Previous page
1/36
Next page
English
INSTALLATION MANUAL
!Caution
Make sure the front glass pane makes full contact with the side pane (there may be no opening between the side
pane and front pane).
If the front and side glass panes do not connect:
Ø
Loosen the self-tapping screws and nuts of the side pane clamp strips by a few turns.
Ø
Slide the side pane tightly against the front pane.
!Caution
Make sure there is no sealing tape between the front and side panes (where the panes connect).
Ø
Tighten the self-tapping screws and nuts of the clamp strips.
5.11Settingtheappliance
The appliance has to be set in such a way that it works correctly with the used concentric system. For that purpose,
a restrictor slide is placed and/or an air inlet guide is removed. The conditions for application with wall terminal
and roof terminal are stated in appendix 2, tables 4, 5 and 6.
5.11.1Airinletguides
!Caution
There are no air inlet guides in the G31 appliance, so they do not have to be removed.
Ø
Check tables 4, 5 and 6 to see whether the restrictor slide has to be removed in your set-up.
The air inlet guides (L) are at the rear at the bottom of the combustion chamber of the appliance (see Appendix 3,
fig. 10 and 11).
Follow the procedure below when removing:
Ø
Remove the glass pane as described in section 5.10.1.
Ø
Remove the two self-tapping screws in the bottom of the combustion chamber (see Appendix 3, fig. 10).
Ø
Remove plate (M) as indicated (see Appendix 3, fig. 10).
Ø
Fully remove the four self-tapping screws of the two air inlet guides (see Appendix 3, fig. 11).
Ø
Remove the two air inlet guides (L).
Ø
Screw back the four self-tapping screws in the combustion chamber.
Ø
Place the plate (M) back in the combustion chamber.
Ø
Screw back the two self-tapping screws in the combustion chamber.
Ø
Place back the glass pane, as described in section 5.10.2.
!Caution
All self-tapping screws must have been screwed back in the combustion chamber.
Do not throw away the air inlet guides, you may need them in the future.
!Tip
If you are installing an appliance, whereby a restrictor slide has to be placed, do not yet place back the glass pane.
5.11.2Restrictorslide
The restrictor slide (R) must be adjusted to the right position (see Appendix 3, fig. 12).
Proceed as follows:
Ø
Remove the glass pane as described in section 5.10.1.
!Caution
The restrictor slide should be placed in the correct manner. Therefore, accurately observe the instructions in
Appendix 3, fig. 12.
Ø
Loosen the 2 self-tapping screws by a few turns, but not fully.
Ø
Adjust the position of the restrictor in accordance with tables 4, 5 and 6.
In the restrictor slide, 4 of the 5 possible positions are indicated by means of 4 cut out letters. B, C and
D correspond with the letters in table 5, the O is indicated in table 4.
Ø
Make sure that the point of the triangle belonging to the position that you want and the centre of the self-tapping
screw are exactly aligned.
!Caution
At restriction D, the restrictor slide should be placed fully towards the front.
Ø
Now tighten the 2 self-tapping screws.
At position A, the restrictor slide should be fully removed from the combustion chamber.
Proceed as follows:
Ø
Remove the 2 self-tapping screws of the restrictor slide from the combustion chamber (see appendix 3, fig. 12);
Ø
Remove the restrictor slide (R);
Ø
Screw back the self-tapping screws in the combustion chamber;
!Caution
The self-tapping screws of the restrictor slide must have been screwed back in the combustion chamber.
Do not throw away the restrictor slide, you may need it in the future.
Ø
Place back the glass pane, as described in section 5.10.2.
!Tip
If you are installing an appliance, whereby a wood set has to be placed, do not yet place back the glass pane.
13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DRU Diablo Next at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DRU Diablo Next in the language / languages: English as an attachment in your email.

The manual is 4.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DRU Diablo Next

DRU Diablo Next User Manual - English - 20 pages

DRU Diablo Next Installation Guide - German - 36 pages

DRU Diablo Next User Manual - German - 20 pages

DRU Diablo Next Installation Guide - Dutch - 36 pages

DRU Diablo Next User Manual - Dutch - 20 pages

DRU Diablo Next User Manual - Dutch - 16 pages

DRU Diablo Next User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info