25125

Dremel 400seriesXPR Manual

14
Zoom out
Zoom in
Previous page
1/72
Next page
14
"V" Notch
MAINTENANCE
Preventative maintenance
performed by unautho-
rized personnel may result in misplacing
of internal wires and components which
could cause serious hazard. We recom-
mend that all tool service be performed
by a Dremel™ Service Facility.
To avoid injury from unex-
pected starting or electri-
cal shock, always remove plug from wall
outlet before performing service or clean-
ing.
Carbon Brushes
The brushes in your tool have been engi-
neered for many hours of dependable serv-
ice.
To prepare the brushes for use, run the tool
at full speed for 5 minutes under no load.
This will properly “seat” the brushes, and
extend the life of the tool.
To maintain peak efficiency of the motor,
examine the brushes for wear every 40-50
hours.
Using the tool with worn
brushes will permanently
damage the motor.
Use only original Dremel™ replacement
brushes.’
Inspect the rotary tool brushes after 40-50
hours of use. If the rotary tool runs erratical-
ly, loses power, or makes unusual noises
check the brushes for wear and possible
replacement. Remember: brushes in the
rotary tool are similar to oil in a car; the more
you check/service, the better the perform-
ance.
Follow these steps to check/change the
rotary tool brushes.
1. With the power cord unplugged, place
the tool on a clean surface. Use the tool
wrench to pry up and release the clip on
the brush cover (Figure A).
2. Remove the brushes from the tool by
pulling the shunt and brass clip which
are attached to the brush (Figure B).
NOTE: Be sure to note how the brass clip
slides out of the slot next to the brush pock
-
et. Also, note how the detent on brass clip fits
into brush pocket slot, which secures the
brass clip into proper position.
3. Check each brush for wear
. If brush is
less than 3/8" long, or if contact end is
rough or pitted, replace the brush.
WARNING
!
WARNING
!
2
4
Removing Brush Cover
Removing/Inspecting Brushes
Installing Brushes
CAUTION
!
A
B
C
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 400seriesXPR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 400seriesXPR in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info