768206
35
Zoom out
Zoom in
Previous page
1/52
Next page
12.0 INFORMATION MENU
R699820 - Yunzi Series User Manual 35
11.4 ECO Mode
This setting when set to On will minimizes the power consumption in the Standby Mode. Additionally, this product
will automatically switch Off whenever the input signal is interrupted for 30min.
11.5 Communication Terminal
Sets the input to which the control device is connected to. It is not possible to use both RS-232C and LAN inputs at
the same time. Settings: RS-232C, LAN.
11.6 Network
When the Communication Terminal selected is LAN, this unit will be visible on the local Network and the following
parameters need to be configured. See “LAN protocol”, page 46 for more details.
11.7 Remote Code A or B
Select in the projector menu the code A or B according to the code selected on the RCU. You can change the code
used by the RCU to communicate with the projector from A to B. To do so, press and hold for 3 sec simultaneously
[MENU]+[BACK] buttons on the RCU. All the buttons on the RCU will blink.
•Two blinks indicate that B code is used.
Three blinks indicate that A code is used.
11.8 Lamp Reset
Resets the lamp use time to "0" during the lamp replacement procedure. See “Replacing the Lamp”, page 37 for
more details.
12.0INFORMATION MENU
Input Terminal
Displays the active video input.
Input Source Format
Displays the type of the current video input signal. If PC input is selected, this item cannot be displayed.
Deep Color Depth
Display the bit depth (color depth) of the video signals input from the HDMI terminals. Deep Color is not displayed
for YCbCr 4:2:2 signals.
Resolution
If the active input is PC input., its resolution is displayed.
H. Frequency
In the case of PC signal, the horizontal frequency is displayed.
V. Frequency
In the case of PC signal, the vertical frequency is displayed.
Lamp Time
Displays the accumulated hours of usage of the lamp.
Calibrator
Stores up to 18 ASCII characters set by the Calibrator. Shown only if set during ISF profile adjustment.
NB: When Eco Mode is On, this unit may no longer be switched On from Standby Mode by using RS-232C
or LAN communication.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DreamVision Yunzi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DreamVision Yunzi in the language / languages: English as an attachment in your email.

The manual is 2,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info