768203

DreamVision Siglos X-TRA Manual

29
Zoom out
Zoom in
Previous page
1/44
Next page
DISPLAY SETUP
R699890 - Siglos X-tra Series User Manual 29
11.7  Screen Adjust and Screen No.
This setting corrects the color balance derived from the reective characteristics of the screen without altering the
global picture settings. You may select the best template available in the Screen No.
a) 001 - 009: select a prole between 001 and 009 when watching 3D content with 3D shutter glasses. Prole
001 is recommended when using Dreamvision’s active 3D glasses.
b) 010 to 255: select the best compensation prole depending on your screen and environment.
12.0 DISPLAY SETUP
Back Color
Congures the screen color displayed when there is no active input. Set to Blue or Black.
Menu Position
Upper left, Upper right, Center, Lower right, Lower left.
Signal Display
On: Display the source of the input signals after input selection. Off: Don’t display.
Logo
On: Display D-ILA logo during startup for 5 seconds. Off: Don’t display.
Language
Choose the OSD language between: English, Japanese, German, Spanish, Italian, French, Portuguese, Dutch,
Swedish, Norwegian, Russian, Chinese or traditional Chinese.
13.0 FUNCTION
13.1  Trigger
The 12V trigger output can be used to control any compatible devices such as motorized screens or anamorphic
kits: The 12V trigger output is 12Vcc, 100mA. Select the trigger output behavior:
• Off: 12V trigger voltage state is always low.
• On (Power): 12V trigger state is high when the projector is powered ON. To be used with motorized screens.
• On (Anamo): 12V trigger is high only when Anamorphic Mode A or Mode B is engaged. To be used with
motorized anamorphic kits.
13.2  O󰀨-Timer
You can congure this automatic power Off function that will switch off the projector when there is no operation
or after a determined timer. Choose the duration of the timer between: Off, 1 hour, 2 hours, 3 hours and 4 hours.
13.3  ECO Mode
This setting when set to On will minimizes the power consumption in the Standby Mode. Additionally, it will
automatically switch Off this unit whenever the input signal is interrupted for 20 minutes.
If ECO Mode is set to On, RS232 and LAN protocol cannot be used during standby mode.
13.4  Network
When the Communication Terminal selected is LAN, this unit will be visible on the local Network and the following
parameters need to be congured. Refer to section “17.2 LAN protocol”, page 37 for more details.
13.5  Remote Code A or B
Select in the projector menu the code A or B according to the code selected on the RCU. You can change
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DreamVision Siglos X-TRA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DreamVision Siglos X-TRA in the language / languages: English as an attachment in your email.

The manual is 4,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info