745853

Dovre Sense 203GA Manual

51
Zoom out
Zoom in
Previous page
1/204
Next page
Subject to change because of technical improvements
11
Converting an existing chimney
pipe
If the home already has a chimney, you can lead the
concentric duct system through the existing chimney
pipe. You can also convert the existing pipe into a con-
centric pipe using a single-wall flexible hose and the
right pipe reducers. There is a conversion kit for this.
See the chapter “Installation requirements” for the con-
ditions under which this conversion is permitted.
The following parts are required to convert an existing
flue into a closed system; see next figure.


09-20021-363
1 The hearth or stove to be connected
2 Concentric duct, 100/150 mm, modular
3 Installation plate inside, square 300 mm
4 Single-wall slide, round diameter 97 mm
5 Parker screws (4 pc)
6
Flexible stainless steel 316L hose, single-
wall round diameter 100/107 mm (heat res-
istance 600°C)
7
Stainless steel hose clamp reach diameter
90 to 165 mm
8 Existing chimney or flue pipe
9 Installation plate outside, square 300 mm
10
Clamping strap (included in delivery of part
11)
11 Roof sleeve
The conversion set consists of parts 3, 4, 5, 7 and 9.
Follow the instructions below for assembly and see
the figure above.
1. Lead the flexible hose (6) through the existing pipe
(8).
2. Attach the slide (4) to the lower end of the flexible
hose and secure it with two Parker screws (5).
3. Keep the bottom of the slide even with the bottom
of the pipe or the ceiling. Cut the flexible hose at
approximately 100 mm above the chimney cap.
4. Attach the installation plate-outside (9) to the flex-
ible hose, clamp it with a hose clamp (7) and
secure it all with a Parker screw (5).
5. Attach the installation plate-outside (9) watertight
to the chimney cap with silicon sealant and stain-
less steel screws.
6. Install the roof sleeve (11) and secure it with the
clamping strap included in the delivery (10).
After the roof sleeve is installed, the slide (4)
should extend about 100 mm under the pipe or
ceiling.
7. Attach the installation plate-inside (3) gastight on
the bottom of the flue or on the bottom of the ceil-
ing with silicon sealant and stainless steel
screws.
8. Place the stove (1) as indicated in the chapter
“Installation requirements”.
9. Connect the stove with the lower end of the flue
using concentric components (2). All components
must overlap at least 30 mm and be secured with
clamping straps or stainless steel Parker screws
to prevent them from coming apart. Extend the
concentric pipe at least 100 mm into the existing
flue.
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dovre Sense 203GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dovre Sense 203GA in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info