745853

Dovre Sense 203GA Manual

50
Zoom out
Zoom in
Previous page
1/204
Next page
10
Subject to change because of technical improvements
09-20021-362
1. Start at the stove and add the concentric pipes
one component at a time along the route you
decided on in advance.
2. Next, install a concentric elbow and possible hori-
zontal change in direction and decide on the loc-
ation of the sleeve.
3. Make a 10 mm larger hole in the facade in such a
way that the air intake duct drains to the outside.
Use a 1 - 3 degree angle or a slope percentage of 2
-5% for this.
Prevent dust and/or grit from getting into the
stove when drilling.
4. Decide on the length of the facade sleeve and
shorten the intake to the wall if necessary. Allow
the flue gas duct to extend approximately 10 mm
from the air intake duct.
Use tin-snips to shorten the air intake cover
(0.5 mm).
Use a hacksaw to shorten the flue gas duct
(0.6 mm).
Grinding is not recommended as it burns stain-
less steel.
5. Remove burrs and sawdust.
6. Extend the facade sleeve through the facade from
the outside, with the “TOP” up, connect to the con-
centric elbow and attach it to the outside of the
facade (make sure the air intake cover drains to
the outside).
7. If so desired, the hole on the inside of the wall can
be finished with a wall plate.
Facade sleeve through facade of
flammable material
Read the "Installation Conditions" chapter care-
fully and follow the installation instructions
below.
1. Follow instruction steps 1 and 2 in the preceding
section.
2. Make a hole in the facade in such a way that the
sleeve is and remains at least 50 mm away from
flammable material all around. This can be done in
the following two ways; see the illustration below.
a. Use a protective duct (1) of non-flammable
material with a diameter of 250 mm.
b. Make a tube (2) of non-flammable material,
250 mm square.
Prevent dust and/or grit from getting into the
stove when drilling.
3. Follow instruction steps 4, 5 and 6 in the preceding
section.
4. Always use centering plates (3) to center and fin-
ish the facade sleeve.
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dovre Sense 203GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dovre Sense 203GA in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info