Manual Dovre Sense 203GA (page 46 of 204) (English, German, Dutch, French, Spanish)

745853

Zoom out

Zoom in

1/204

Subject to change because of technical improvements

All elements of the air supply and the flue gas

exhaust system must be inserted at least 30 mm

into each other and be secured against coming

loose using clip bindings.

The duct must be kept in its position by means of

wall brackets and centring plates. The maximum

distance between the wall brackets is 2 metres.

The flue gas exhaust system and the outlet must

satisfy any local regulations that apply. This is a

closed appliance of type C11 or C31 (depending on

the choice of wall or roof sleeve).

The flue must end in a zone that is not affected by

surrounding buildings, trees close by or other

obstacles.

For outlets that are in the vicinity of a boundary par-

tition or ventilation opening, see the national and

regional regulations regarding this.

In the case of a wall sleeve, the outlet must be in a

zone such that any contact between flue gas outlet

and/or flue gases and people is impossible and

such that the flue gases cannot accumulate under

overhanging parts of buildings or awnings or such

like.

The flue gas outlet can reach temperatures of

200 °C, while the flue gases can reach 300 °C.

Existing chimney

Type C91

An existing flue gas pipe (chimney) can be converted

into a concentric flue gas exhaust system.

In this case, the following requirements apply to the

existing chimney:

The existing pipe must be leakproof and thoroughly

cleaned.

The pipe must be able to withstand temperatures

up to 600°C along its entire length.

The pipe may change direction no more than one

time, with a maximum change angle of 45° and

along no more than 25% of the total length.

The pipe must have a diameter of at least 150 mm

round or square, and no more than 250 mm round or

square along the entire length. The section may not

be larger or smaller than the specified limits at any

place. The section may vary over the whole length

of the flue pipe on the condition that the transitions

in section occur gradually.

If this last condition cannot be satisfied, the pipe

may be lined with stainless steel flexible piping

with a diameter of 150 to 250 mm, which is heat-

resistant to 600°C before it can be converted into

an air intake pipe.

The flue pipe must be closed at the top and bottom

with the recommended flanges (mounting plates).

The bottom of the flue section must always be con-

nected to the appliance using a concentric duct sec-

tion and the prescribed roof outlet must always be

mounted on the outlet side.

The maximum allowable length, including the con-

nection section (resistance length), is 12 metres.

Every elbow of 90° corresponds to 1 metre of res-

istance length and every elbow up to 45° cor-

responds to 0.5 metres of resistance length.

Floor and walls

The floor on which the appliance is placed must have

sufficient bearing capacity. The weight of the appli-

ance is given in the appendix “Technical Data

appendix”.

Keep sufficient distance between the appli-

ance and combustible materials such as

wooden walls and furniture.

Carpets and rugs must be at least 80cm away

from the fire.

For further requirements with respect to fire

safety, see the appendix "Distance from com-

bustible material".

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dovre Sense 203GA in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 5,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dovre Sense 203GA Manual

Product: