Manual Dovre Sense 203GA (page 45 of 204) (English, German, Dutch, French, Spanish)

745853

Zoom out

Zoom in

1/204

Subject to change because of technical improvements

The appliance must be inspected by the

installer for the air tightness of the gas supply

and flue gas duct. The operation of the control

valve, the thermocouple circuit and the ignition

of the burner must also be checked.

When the appliance is ready for use, have your

installer tell you about its use, operation and

maintenance.

Use only the supplied ceramic wood block set,

coals or stones.

Place the log set exactly according to the

description.

Keep the area around the pilot flame free of

coal.

Avoid dirt in the gas pipe.

Always close the gas valve if the appliance is

not in use.

If you notice a gas smell, immediately close

the main valve, open windows and avoid fire or

the use of electrical contacts, such as

switches, because of the sparks they can

cause. Always call in an expert to trace a pos-

sible gas leak.

Installation

requirements

General

The appliance must be connected tightly to a well-

functioning flue.

For connection measurements: see "Technical

data" appendix.

Ask the fire service and/or your insurance com-

pany about any specific requirements and reg-

ulations.

Concentric flue gas exhaust

system

This closed gas stove was designed in combination

with a concentric flue gas exhaust system from the

manufacturer Muelink & Grol. The appliance can also

be connected to a concentric flue gas exhaust system

from the manufacturers Metaloterm or Poujoulat. Use

the appropriate connection collar (available from your

supplier) and follow the supplier's instructions for the

installation.

Use only original parts from the manufacturers

named above. You can order the elements for the

concentric pipe system (such as wall sleeves, roof

sleeves, tubes and bends, clip bindings and brack-

ets) in the desired quantities via your supplier.

You can find the order codes of the available

elements in the appendix "Materials list for con-

centric flue gas exhaust".

The appliance may not be connected to an existing

flue gas exhaust duct or chimney just like that. An

existing chimney or flue gas exhaust duct can be

used as an active element in the installation under

certain conditions. See the paragraph "Existing

chimney duct".

The appliance has a closed combustion chamber

and must be installed as a closed appliance of type

C11-C31 (depending on the choice of wall or roof

sleeve). With a combined intake-exhaust, the nat-

ural draught of the appliance removes the com-

bustion gases outside. The same natural draught

sucks in the necessary combustion air. The con-

centric flue gas exhaust system can be equipped

with a wall sleeve or a roof sleeve. Use the pre-

scribed wall outlet or roof outlet for this purpose.

A maximum value of 12 metres applies to the total

allowable length of the pipe system (the resistance

length). Every bend of 90° corresponds to 1 metre

of resistance length and every bend up to 45° cor-

responds to 0.5 metres of resistance length.

The horizontal section of the pipe system may

never be longer than the vertical section.

In order to maintain the natural draught, at least one

metre of concentric pipe must be placed vertically

before the wall or roof sleeve is installed.

Before the appliance can be placed, you must

check whether the pipe route desired for your

installation is technically permitted. See the

appendix “Calculation sheet for checking pro-

jected route”.

The distance from ducts and sleeves to com-

bustible material must be at least 50 mm every-

where.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dovre Sense 203GA in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 5,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dovre Sense 203GA Manual

Product: