507712
16
Zoom out
Zoom in
Previous page
1/52
Next page
16
Operating
Starting
WARNING:
Do not start the engine in locations where refueling has
taken place. Move at least three meters away from the place
where the Power Cutter was fuelled.
Failure to do so may cause ames or re.
CAUTION:
Before starting engine, be sure to check that the cutting
disc is not touching the ground or any other obstacle.
If the cutting disc is touching the ground or other obstacle, it
may cause an accident.
As soon as the engine starts, the cutting disc will rotate, so
be fully aware of nearby people and obstacles.
1. Cold-starting
(1) Repeatedly press primer pump until fuel enters it.
(2) Flip switch in direction of
(choke).
(3) Hold down rear handle with a foot and rmly hold down
tubular handle with a hand.
(4) Vigorously pull the start handle repeatedly until the rst ring
up sound is heard.
Warming up
Once engine starts, hold down safety lever, and squeeze and
release throttle repeatedly for one or two minutes to warm up
the engine.
Once engine speed stabilizes and it revs smoothly from low to
high speed, warming up is complete.
2. Starting up when engine is warm
Press the primer pump several times. From the outset, place the
switch in the [I] (operating) position, and start the engine using
task (3) of procedure 1 above.
NOTE:
Repeatedly pulling and releasing the starter grip with the
switch set to choke will ood the engine with fuel, making start
up difcult.
When the engine stops, never squeeze the throttle lever.
Unnecessarily squeezing the throttle lever with the engine
stopping will ood the engine with fuel, making start up
difcult.
If the engine does become ooded with fuel, remove the
spark plug, and slowly pull the starter handle several times to
remove the excess fuel. Also, dry the electrode section of the
spark plug.
Do not pull starter handle to the limit of the rope, as doing so
shortens the lifespan of the rope. Furthermore, gently return
the starter handle without suddenly letting go of it.
Avoid letting the Power Cutter run at maximum idling speed,
as doing so will shorten the lifespan of the engine.
3. Stopping
To stop the engine, release the throttle, and set the switch to the
(Stop) position.
If the choke lever is wrongly moved to the position to stop the
tool, use half throttle to restart.
Throttle lever
Starter grip
Switch
Switch
Safety locking
button
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar PC-7614V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar PC-7614V in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info