507712
18
Zoom out
Zoom in
Previous page
1/52
Next page
18
V-belt
1. Adjusting V-belt tension
If the cutting disc halts in mid operation easily, the V-belt
has slackened. If this is the case, adjust tension using the
following procedure.
(1) Loosen belt cover tightening nuts.
(2) Turn the tension adjustment screw to the right (clockwise)
until the indicator nut reaches the marked position in order to
increase the tension of the V-belt.
(3) Once V-belt tensioning is complete, rmly retighten the belt
cover tightening nuts.
If the cutting disc stops easily even though the tension of the
V-belt has been adjusted, or the V-belt breaks, replace with a
new V-belt.
2. Changing the V-belt
(1) Loosen tightening nut, and turn tension adjustment screw to
the left until the end of the screw is visible.
(2) Remove tightening nuts, and then remove belt cover.
(3) Next, remove the three mounting screws, and remove the
clutch cover.
(4) Remove the old V-belt, and t on a new V-belt. Now,
remount the clutch cover followed by belt cover.
(5) Adjust tension as shown in the Adjusting V-belt tension
section.
Cleaning the protection hood
Over time, the inside of the protection hood can become caked
with material residue (especially from wet cutting), which if
allowed to accumulate can hinder the free rotation of the cutting
disc. For this reason the hood must be cleaned out from time to
time.
Take off the cutting wheel and remove the accumulated material
from inside the hood with a strip of wood or similar implement.
Clean the shaft and all disassembled parts with a cloth.
NOTE: To install the cutting wheel see “Mounting the cutting
disc”.
Tensioning screw
Tensioning screw
Indication nut
Mark
Hex. nut
Hex. nut
Belt cover
Belt cover
End of screw
Clutch cover
IMPORTANT:
Because many of the parts and assemblies not mentioned
in this Instruction Manual are vital to the safety of the unit,
and because all parts are subject to a certain amount of wear
and tear, it is important for your own safety that you have the
unit checked and maintained regularly by a DOLMAR service
center.
IMPORTANT:
If the cutting wheel breaks during cutting, the
Power Cutter must be repaired by a DOLMAR
service centre before being used again!
SERVICE
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar PC-7614V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar PC-7614V in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info