507712
14
Zoom out
Zoom in
Previous page
1/52
Next page
14
Tightening the V-belt / Checking V-belt tension
IMPORTANT:
Exact V-belt tension is essential for maximum cutting
performance with minimum fuel consumption. Improper
V-belt tension will result in premature wear to the V-belt and
V-belt wheel or damage to the clutch bearing.
NOTE: The two hex. nut (9) must be loosened before tightening
the V-belt or checking the tension.
To increase the belt tension, turn the tension screw (10) to the
right (clockwise) with the combination wrench included with the
Power Cutter.
The belt tension is correctly adjusted when the nut (11) is located
as shown in the gure compared to the position of the mark (12).
IMPORTANT:
After tightening/inspection, make certain to tighten
the hex. nut (9) (25 - 31 Nm).
Do not adjust the belt tension while the machine is
hot. There is a risk of burn injury.
Before operating
1. Checking/replenishing engine oil
With the engine in a cool state, check/replenish engine oil in
the following way.
Position engine on a at level, and check to see whether oil is
within the range of MAX and MIN of the oil tank.
If oil is insufcient (near the MIN mark of the oil tank), ll the
oil tank with oil to the MAX mark.
Oil quantity can be checked externally without removing the oil
cap as the oil level can be seen at the external, see-through,
measuring mark window.
For reference, oil needs to be replenished every ten operating
hours (one tank of oil for ten fuel refuels).
Replace extremely dirty or discolored oil.
<Recommended oil> .... Use API grade SF class or higher SAE
10W-30 oil (automobile 4-stroke engine
oil).
<Oil quantity> ...............0.22 L (220 mL)
NOTE:
If the engine is not stored in the upright position, oil will
circulate through the engine, which will mean that there will be
excessive oil in the Power Cutter when replenishing.
If oil exceeds the MAX mark, it may leak out causing dirtying
or white smoke.
Oil replacement Point 1 <Oil cap>
Interval of replacement: Initially, after 20 operating hours, and
subsequently every 30 operating hours.
Clean away the dirt from around oil lling neck and then
remove oil cap.
Place the oil cap on a surface where it will not pick up grit and
dirt. If the cap is put back on in a dirty state, oil circulation may
deteriorate and engine parts become worn, which may cause
mechanical failure.
MAX mark
MIN mark
Oil
The oil is visible from here, so
the MAX and MIN marks can
be used to check the quantity
of oil.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar PC-7614V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar PC-7614V in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info