507712
13
Zoom out
Zoom in
Previous page
1/52
Next page
13
PUTTING INTO OPERATION
CAUTION:
Always turn off the engine and pull off the spark plug cap
before doing any work on the Power Cutter! Always wear
protective gloves!
CAUTION:
Start the Power Cutter only after complete assembly and
inspection.
For the following work, use the assembly tools included with
delivery:
1. 13/16 AF combination wrench
2. Star-sharped wrench
3. Carburetor adjustment screwdriver
4. Adapter ring
Place the Power Cutter on a stable surface and carry out the
following assembly steps:
No air lter is installed!
Before operation, squeeze the supplied lter several times so
that oil is evenly immersed in the entire lter. Insert an oiled
foam lter (pre-lter), as shown in the adjacent illustration! To
do this, take off the lter cover (see the chapter on Cleaning/
changing the air lter).
Mounting the cutting disc
WARNING:
When installing a diamond cutting disc, be sure to mount
it so that the arrow is in the same direction as the outer
ange (6) rotates. Mounting the diamond cutting disc (4) with
its arrow direction opposite to that on the wheel cover may
cause chipping of the disc edge and personal injury.
When installing a cutting disc (4), always use the ring that
matches the bore of the cutting disc and the diameter of
the spindle (5). Failure to use rings that mate may cause tool
vibration resulting in serious personal injury.
Only use cutting discs with the bore that matches the
diameter of the ring(s) provided. Using discs that do not mate
may cause tool vibration resulting in serious personal injury.
Inspect a cutting disc for damage. (see the section titled
“Cutoff discs” in SAFETY PRECAUTIONS.)
1. Insert the star-shaped wrench (2) into the hole (8) to prevent
the spindle (5) from rotating.
NOTE: When the holder of the pressure water system is installed
in the hole in the tool, remove it before mounting the
cutting disc.
2. While holding on the wrench (2) in that position, use the
combination wrench (1) provided and turn the bolt (7) securing
the disc counterclockwise and remove the bolt (7) and outer
ange (6).
3. Mount a diamond cutting disc/cut-off abrasive disc (4) on the
arbor (5). And then put the outer ange (6) on the spindle
so that the two parallel at surface on the outer ange t the
spindle at surface and rmly tighten the bolt clockwise.
To install a cutting disc, mount a ring with the same matching
diameter as the disc bore and the O ring provided to retain the
ring on the spindle before installing a diamond cutting disc.
And then install the cutting disc.
NOTE: Tighten the hex bolt rmly (25 - 31 Nm), as otherwise the
cutting wheel may slip during cutting.
Schematic
drawing
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar PC-7614V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar PC-7614V in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info